background image

11

Troubleshooting

Troubleshooting

NOTE: If you are having problems after installation follow the Trouble-

shooting procedures below.

No LED’s illuminated on the Remote Tuning Module when docked.

1.  Verify Remote Tuning Module is properly seated in crossover housing.

2.  Verify that Ground connection is connected to clean metal on the 

vehicle’s chassis. Repair/replace if necessary.

3.  Verify there is 9 to 14.4 Volts present at the power source. Verify 

quality connection at power source. Repair/replace if necessary.

4.  Check fuse(s) on power source. Replace if necessary.

No LED’s illuminated on the Remote Tuning Module when tethered

.

1.  Verify that Remote Tuning Module functions correctly when docked. 

See Step 1.

2.  Verify tethering cable is securely connected at the Remote Tuning 

Module as well as at the crossover connection port. Repair/replace 

if necessary.

All the LED’s are illuminated on the Remote Tuning Module when 

docked.

1.  Push both the Tweeter 

Level Right button and the 

Woofer Freq. Left button 

simultaneously for 5 seconds, 

then release.

All the LED’s are illuminated on the Remote Tuning Module when 

tethered.

1.  Verify that Remote Tuning Module functions correctly when docked. 

See Step 3.

2.  With the crossover power on re-dock the Remote Tuning Module. 

Allow to remain docked for 5 seconds, then attempt to tether again.

The LED’s of the Remote Tuning Module remain illuminated with 

vehicle turned off.

1.  Ensure use of a switched 12 Volt source for power source of the 

Remote Tuning Module.

No sound from 1 or more of the component speakers.

1.  Verify quality connections for the speaker wires at amplifier, crossover, 

and speaker terminal.

2.  Verify the crossover jumpers are all installed for standard wiring 

option or all removed for bi-amp wiring option. See installation-

wiring. 

TWEETER LEVEL

(dB)

-4

-4

-2

-2

0

0

0

0

3

6

6

12

12

3

2.5

2.5

180

180

+2

+2

(deg)

(kHz)

(dB/oct)

WOOFER FREQ.

WOOFER SLOPE

REMOTE TUNING MODULE

TWEETER PHASE

Содержание Power T5652-S













Отзывы: