Roche Cedex Bio Скачать руководство пользователя страница 13

Страница: 13 / 496

Roche Diagnostics

Operator’s Manual · Version 3.1

A-5

Cedex Bio System

1 Safety

Safety classification

Safety classification

Before you attempt to use the

Cedex Bio

instrument, you must be fully familiar with

the following symbols and their meanings:

Safety information

Before operating the

Cedex Bio

instrument, it is essential that you both read and

understand the safety information listed below.

Read all Roche safety notices carefully and make sure you understand them.

Transport

Electrical safety

WARNING

Warning

Indicates a hazardous situation which, if not avoided, could result in death or serious
injury.

CAUTION

Caution

Indicates a hazardous situation which, if not avoided, may result in minor or moderate
injury.

NOTICE

Notice

Indicates a hazardous situation which, if not avoided, may result in property damage.

WARNING

Injury from heavy loads

You may injure your hands, fingers, or back when putting the analyzer in place. Carry the
analyzer according to the transport instructions.

WARNING

Electrical shock by electronic equipment

Do not attempt to work in any electronic compartment. Installation, service, and repair
must only be performed by authorized and qualified personnel.

Electrical safety

Connect the analyzer to grounded power outlets only (IEC protection class 1). All periph-
eral devices that are connected to the

Cedex Bio

instrument must comply with safety

standard IEC 60950 for information technology equipment, or with IEC 61010-1, UL 61010-
1 for laboratory use instruments.

Содержание Cedex Bio

















































































































































































































































































































































































































































































































Результаты поиска

Содержание Cedex Bio

Отзывы:

Roche Cedex Bio, Руководство оператора, Страница: 13 / 496

Результаты поиска

Содержание Cedex Bio

Отзывы: