Robust Sweet 16 страница 15 Скачать руководство пользователя | Manualshive

Страница: 15 / 18

background image

14

ASSEMBLING THE OPTIONAL CASTER KIT

Special Note: One bar gets two straight casters,
put it on the headstock end. The other bar gets a
single swivel caster in the center, it goes on the
tailstock end.

Assemble as shown in the picture below.  Please
note the orientation of the ball joints.  The
threaded studs must point towards the back of
the lathe on both bars.  Also, when attaching the
ball joints to the frame, the wrench flats should
be vertical.

Raise casters before turning.

Using the Casters:

Press down on the handle to engage the casters. Pull up on the handle to disengage.

Casters lowered for moving the lathe Casters raised when turning

Ball Joint threaded stud must point
towards back of lathe on both bars.
Wrench flats must be vertical.

«
...
13
14
15
16
17
...
»

Содержание Sweet 16



















Отзывы:

Нет отзывов

Похожие инструкции для Sweet 16

Бренд: Haas Automation Страницы: 14

Бренд: Handler Страницы: 8

Бренд: Jet Страницы: 24

Бренд: Trak Machine Tools Страницы: 7

Бренд: Sima Страницы: 22

Бренд: Meec tools Страницы: 70

Бренд: Luna Страницы: 80

Бренд: Amco Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды