Deck lights for indoor or outdoor use, with 3 super bright light emitting
diodes (L.E.D) with cable with double insulated safety isolation
transformer with Safety Extra Low Voltage (SELV) equivalent output.
Protection against electric shock: Luminaires Class III, (SELV)
Transformer: Class II, SELV equivalent output.
Dimensions: Top flange diameter 30mm, 0.5 mm thick
Body diameter 20mm, depth 25mm Cut -out size 22mm
Junction box: (L) 140mm, (W) 115mm, (D) 38mm. IP44
Supply: 220V-240V AC 50Hz (approx 10W incl. transformer)
Ta range: -20°C < ta < +40°C
CABLE LENGTH
：
Flex cable from transformer 2m
Transformer to junction box 5m
Junction box to fitting 5m
Suitable for mounting on normally flammable surface, e.g. wooden
decking
Luminaire protection: IP68
Transformer protection: IP44,
Rain proof: Do not locate where water may pool
1 Ensure mains supply is switched off before commencing work.
2 Location:
Avoid: positions in decking centre where pedestrian may trip on
edge of light. Check wiring path layout, cable lengths, and suitable
transformer locations etc before commencing work. If connector
between transformer and fittings (low voltage output line) is to be
buried, ensure that drainage is provided so that junction point does
not become waterlogged.
3 The body may be fixed directly into wooden decking. This requires a
cut-out hole 22mm diameter in the deck.
4 The transformer and luminaires must be connected to the junction
box. Unscrew top of junction box and remove rubber seal. Connect
luminaire plugs through the cut outs in the 2 sides of the junction
box. The transformer plug must be connected through the top cut
out. Replace rubber seal and top of junction box and tighten screws.
5 Safety note! The transformer or junction box must not be buried
in the ground. It is protected against water splashes but must
not be located where it may become waterlogged. The power
supply cord must not be exposed to mechanical damage. For
correct mounting of junction box please refer to Figure 2
6 Use only with a mains supply that is protected by a residual
current circuit breaker (RCCB).
7 This kit has no user serviceable parts. If mains wiring or
transformer is damaged, disconnect from mains and discontinue
use.
Stainless Steel Fittings – General Maintenance Instructions
The stainless steel trim on this product has very high resistance to
corrosion. Despite this, blotches may appear on the surface of the
stainless steel. They can be removed by a soft cloth soaked with
neutral oil (WD-40 or equivalent). The cause of the blotching is
due to some free iron atoms from the polishing wire brushes
remaining on the surface and these atoms are outside the
protection afforded by the nickel and chrome alloys in the steel.
Note:
- If the product is exposed to very corrosive environmental
conditions (sea fronts, salty atmospheres etc) it will require
additional maintenance. Before installing, the stainless steel parts
must be treated with neutral oil, which must penetrate all the joints.
After treatment, dry with a soft cloth. In very corrosive
environments, the treatment with oil must be repeated at least 4
times a year. In cases of serious corrosion use an abrasive paste
(specifically designed for stainless steel or chrome) to remove the
stain and then apply the neutral oil again.
Attention:
Wood preservative and solvents can damage insulation
on electric cables. Allow treatment to dry prior to installing deck
lights. Do not apply preservatives after installing.
LED DECKING KITS
R3LED5S IP68 5 Fitting Kit, Circular (3 SMD LEDs)
R3LED10S IP68 10 Fitting Kit, Circular (3 SMD LEDs)
Issue 2 200415
Page 1
Specifications
Installation
Information for the Product user:
1. Please note the requirement to dispose of Waste Electrical & Electronic Equipment separately from household waste (WEEE marked with
crossed out wheelie bin symbol).
2. Please consider your role in contributing to re-use and recycling by returning this product at end of life to a collection centre for waste electrical
equipment or a Civic Amenity site, or to a retail outlet from which you are purchasing a replacement.
3. This equipment may contain substances that are hazardous to health and the environment if disposed of carelessly. It is important that it is
separated from normal household waste and recycled in the WEEE chain
4. The “crossed out wheelie bin symbol” on a product indicates this equipment must not be disposed of in normal household waste, but should be
disposed of according to local WEEE regulations
The Installation must be carried out by an electrician
ISO 9001:2008
Q UAL IT Y ASSU RED CO MPANY
Instruction manual
LED Group
Western Retail Park
Tel: +353 1 7099000
Nangor Road
Fax: +353 1 7099060
Dublin 12
Email: [email protected]
Ireland
Website: www.led.ie
PLEASE READ INSTRUCTION BEFORE COMMENCING INSTALLATION AND RETAIN FOR FUTURE REFERENCES.
! Electrical products can cause death or injury, or damage to property. If in any doubt about the installation or
use of this product, consult a competent electrician
Note:
Product technical information and specification may change over time without prior notification
For the latest technical information please visit our web site www. ledgrouprobus.com or robusdirect.com
