Specification:
Installation:
Information for the Product user
Stand alone Passive infra-red sensor switch (PIR). Replacement for standard
single gang wall switch. Energy saving lighting control, which is ideal for indoor,
outdoor and wall.
Electrical Protection:
Supply:
Output Load:
Operating Temp:
Size:
Weight:
Detection range:
Delay time:
Light Level Adjustable:
IP:
Terminals suitable for cable sizes from 0.75mm2 to 1.5mm2.
Suitable for mounting on normally flammable surface
Note:
Product technical information and specification may change over time without prior
notification. For the latest technical information please visit our web site
www.ledgrouprobus.com or www.robusdirect.com
Class II (no earth required)
220V~240V 50/60Hz
Max.1,000W Incandescent lamps
300W fluorescent lamps, 150W LED
5°C < ta < 40°C
Height: 85mm, Depth: 130mm, Width: 75mm
0.36Kg
180° detection angle, 12m Range,
2.5m Max Mounting Height
Adjustable time delay10 second to 10minutes
Daylight to night adjustable
IP44
! Electrical products can cause death or injury, or damage to property. If in any
doubt about the installation or use of this product, consult a competent electrician.
1. Ensure mains supply is switched off before commencing work.
2. Choose suitable location for mounting the sensor, mounting height is 2m to 2.5m from
floor level.
3. When cutting or drilling holes ensure not to impinge on buried cable or pipe work.
Avoid:
positions close to exhaust gas flues, heat extraction vents, or heat sources to
avoid false triggering. Also avoid pointing toward bright lights which may prevent
operation (or cause hunting i.e. flashing lights on and off) when Lux level set for night
operation.
4
.
Connect detector LS(black) to lamp L,connect detector L(brown) to power suplly L,
and connect detector N(blue) to power supply N and lamp N.
5. Set Lux control to day or sun position and Time to minimum (-).
6. Put switch in the on position and attach sensor to wall.
7. Switch on mains supply: The sensor will warm-up for approx 50 seconds and then
switch to auto detection mode.
8.The connected lights can be switched by two ON/OFF operations of the external switch
within 4 seconds, the light will flash 3 times and then the light stay on for 8 hours;If you
want to make the detector back to the AUTO mode,you can operate the external
switch ON/OFF two times within 3 seconds, the light will flash 3 times and then the
detetor will return to the AUTO mode(normal operation)
Walk testing can then be carried out to determine detection area with slow walking pace.
When the sensor detects movement, the load will be switched on for the preset time.
When finished, set light level and delay time. Turning the Lux control toward the moon
position will stop switching action during bright daylight (for energy saving). To increase on
time turn time control t, max time delay 10 minutes. Note: once sensor has been
triggered, subsequent detection restarts timing period from beginning, so light stays on
until set time elapses after last triggering
1. Please note the requirement to dispose of Waste Electrical & Electronic Equipment separately from household waste (WEEE marked
with crossed out wheelie bin symbol).
2. Please consider your role in contributing to re-use and recycling by returning this product at end of life to a collection centre for waste
electrical equipment or a Civic Amenity site, or to a retail outlet from which you are purchasing a replacement.
3. This equipment may contain substances that are hazardous to health and the environment if disposed of carelessly. It is important
that it is separated from normal household waste and recycled in the WEEE chain
4. The “crossed out wheelie bin symbol” on a product indicates this equipment must not be disposed of in normal household waste, but
should be disposed of according to local WEEE regulations
Issue 5 150414
Motion Detector 180
°
PIR
R180-01 & R180-04
Please read instruction before commencing installation and retain
for future reference.
The Installation must be carried out by an electrician
LED Group
Western Retail Park
Tel: +353 1 7099000
Nangor Road
Fax: +353 1 7099060
Dublin 12
Email: [email protected]
Ireland
Website: www.led.ie
Page 1
ISO 9001:2008
Q U A L I T Y A SSU R E D C O M PA N Y
