ROBEL 62.05L страница 9 Скачать руководство пользователя

Страница: 9 / 151

2. Safety

Safety

2.1

Designated use

The vibratory tamper 62.05L has been designed and manufac-
tured for is used in track construction to compact the ballast
bed under the sleepers

2.2

Foreseeable misuse

The vertical tamper must not be used for demolition work or
the like.

2.3

Conventions of layout

These instructions make use of the following warning texts and
symbols to keep the operator safe and injury-free and prevent
damage to the material assets of the operating company:

DANGER

Indicates that non-compliance with the in-
structions will result in death or severe (irre-
versible) injuries of the operating personnel.

WARNING

Indicates that non-compliance with the in-
structions may result in death or severe (irre-
versible) injuries of the operating personnel.

CAUTION

Indicates that non-compliance with the in-
structions may result in minor (reversible) inju-
ries of the operating personnel.

NOTICE

Points out that non-compliance with instructions may result
in damage to the product or other assets of the operating
company.

Contains important information about the
product, its operation or about a section of the
instructions on hand.

Содержание 62.05L
























































































































































Результаты поиска

Содержание 62.05L

Отзывы:

Похожие инструкции для 62.05L

Бренды по названию

Популярные бренды

ROBEL 62.05L, Руководство по эксплуатации

Результаты поиска

Содержание 62.05L

Отзывы:

Похожие инструкции для 62.05L

Бренды по названию

Популярные бренды