background image

 

 

 

Page: 1 

 

 

INTRODUCTION 

Congratulations  on  your  purchase  of  this  quality  ROBAND

®

  product.    With  proper 

care  and  management  your  new  purchase  will  give  you  years  of  trouble  free 
service. 

By  reading  these  instructions  carefully  you  can  ensure  that  this  machine  is  used 
and maintained properly, helping your new investment to perform well for you now, 
and to continue performing in the many years to come.

 

GENERAL PRECAUTIONS 

This machine must only be operated by qualified person(s) who are fully versed in the 
operating and safety instructions described in this manual.  Servicepersons should be 
instructed  to  familiarise  themselves  with  any  and  all  safety  instructions  described  in 
this manual prior to commencement of any maintenance or service. 

In  the  case  of  new  personnel,  training  is  to  be  provided  in  advance.    These 
machines should not be operated by persons (including children) with reduced 
physical,  sensory  or  mental  capabilities,  or  lack  of  experience  or  knowledge, 

unless they have been given supervision or instruction concerning the safe use of the 
appliance by a person responsible for their safety. 

These  machines  are  heating  units,  and  as  with  any  commercial  heating  unit  the 
surfaces on these units will get hot.  Always be careful when near an operating Bain 
Marie,  and  ensure  that  any  risk  to  unwary  customers  or  staff  is  minimised  with 
additional  signage  if  necessary.    Due  to  the  obvious  heat  hazard  Roband 
recommends that these units be kept out of reach of children. 

The  performance  of  this  unit  cannot  be  guaranteed  for  operational  use  outside  its 
design parameters. 

The machine should be disconnected from all power and allowed to cool before 
cleaning.  

Roband will accept no liability if; 

  Non-authorised personnel have tampered with the machine. 

  The instructions in this manual have not been followed correctly. 

  Non-original spare parts are used. 

  The machine is not cleaned correctly, with the right product. 

  There is any damage to the unit. 

  The machine has been modified in any way. 

 

 

Содержание BM14

















Отзывы: