manualshive.com logo in svg

RKI Instruments GasWatch 3, Руководство оператора

Поделиться
Скачать
RKI Instruments GasWatch 3 Скачать руководство пользователя страница 84

84 • Appendix A: Maintenance Mode

GasWatch 3 for CO and O

2

3. Use AIR to scroll to the item whose replacement date you want to view or change.

4. To change the replacement date:

a.  With the desired item displayed, press and release POWER/MODE.
b.  Press and release POWER/MODE again to set the replacement date to the current 

date. 

5. Use the AIR button to scroll to 

ESCAPE

. 

6. Press and release POWER/MODE to return to the 

SEN.DATE

 item in Maintenance 

Mode. 

7. See “Entering Measuring Mode (START)” on page 90 to enter Measuring Mode.

Performing a Bump Test (BUMP)

See “Performing a Bump Test (BUMP)” on page 37 for a description of the 

BUMP

 item.

Setting Alarms to Latching or Self-Resetting (LATCH)

ON 

(factory setting): The GasWatch 3 remains in alarm until the alarm condition passes 

and

 

POWER/MODE is pressed.

OFF

: The GasWatch 3 automatically resets an alarm when the alarm condition passes.

1. While in Maintenance Mode, press AIR to scroll to 

LATCH

.

2. Press and release POWER/MODE. The current setting flashes. 
3. Use AIR to display the desired setting.
4. Press and release POWER/MODE to save the setting and return to the 

LATCH

 item in 

Maintenance Mode.

5. See “Entering Measuring Mode (START)” on page 90 to enter Measuring Mode.

ESCAPE

    

     

     

  

 

 

           AIR

      AIR                                         AIR                                         AIR

CO

    

   

   

 1 .  1

  

 2019

 

O2

    

     

     

 1 .  1

  

 2019

 

BATTERY

    

     

     

 1 .  1

  

 2019

 

LATCH

    

     

     

  

Содержание GasWatch 3
































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды