RKI Instruments GasWatch 3 Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 95

background image

GasWatch 3 for CO and O

2

Appendix A: Maintenance Mode • 83

Performing a Gas Test

1. While in Maintenance Mode, press AIR to scroll to

GAS.TEST

.

2. Press and release POWER/MODE. The current gas reading displays. The bottom of the

LCD alternates between “GAS.TEST” and “BUZZ.OFF”.

3. Turn the regulator knob counterclockwise to open the regulator.
4. The instrument initiates alarm indications except for the buzzer. There is no buzzer

indication in the

GAS.TEST

menu even though the buzzer sounds in the event of a real

gas alarm condition.

5. Turn the regulator knob clockwise to close the regulator.
6. Unscrew the regulator from the calibration cylinder.
7. Remove the calibration cup from the GasWatch 3.
8. Store the calibration kit in a safe and convenient place.
9. Press and release POWER/MODE to return to the

GAS.TEST

item in Maintenance

Mode.

10. See “Entering Measuring Mode (START)” on page 90 to enter Measuring Mode.

Sensor/Battery Replacement Date (SEN.DATE)

The

SEN.DATE

item allows you to keep track of when the sensor and the battery were

replaced.
1. While in Maintenance Mode, press AIR to scroll to

SEN.DATE

.

2. Press and release POWER/MODE. The sensor replacement date displays.

GAS .TEST

GAS .TEST

20.9

%

0

ppm

BUZZ .OFF

20.9

%

0

ppm

SEN .DATE

«
...
81
82
83
84
85
...
»

Содержание GasWatch 3
































































































Отзывы:

Нет отзывов

Похожие инструкции для GasWatch 3

Бренд: NodeTalks Страницы: 28

Бренд: Berner Страницы: 33

Master-200 Edition

Бренд: Winbest Страницы: 10

Бренд: Decatur Electronics Страницы: 76

Бренд: REX Страницы: 12

Бренд: PureAire Страницы: 34

M-59 Treasure Master

Бренд: White’s Electronics Страницы: 8

Coinmaster 2/DB

Бренд: White’s Electronics Страницы: 8

Бренд: White’s Electronics Страницы: 32

Бренд: White’s Electronics Страницы: 29

Бренд: Valentine One Страницы: 40

Бренд: Honeywell Страницы: 6

Бренд: AKO Страницы: 2

Бренд: RPB Страницы: 24

Бренд: Gold Digger Страницы: 6

Бренд: Gold Digger Страницы: 9

Бренд: Gold Century Страницы: 9

Бренд: Gold Century Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды