manualshive.com logo in svg

RKI Instruments GasWatch 3, Руководство оператора, Страница: 31 / 95

Поделиться
Скачать
RKI Instruments GasWatch 3 Скачать руководство пользователя страница 31

GasWatch 3 for CO and O

2

Chapter 4: Display Mode • 31

2. Press AIR to enter the 

BP.DATA

 screen and switch between the channels. 

3. When you are done viewing the last bump test date, press and release POWER/MODE to 

return to the 

BP.DATA

 screen in Display Mode.

Date/Time Screen (DATE)

The 

DATE

 screen shows the instrument’s date and time. 

Temperature Screen (TEMP)

The 

TEMP

 screen shows the surrounding area’s temperature. 

Alarm Points Screen (ALARM--P)

The Alarm Points Screen shows the gas alarm settings.
1. After entering Display Mode, press and release POWER/MODE until the 

ALARM--P

 

screen sequence appears.

CO

    

     

     

  1 . 1

2019

O2

    

     

     

 1 . 15

2019

    AIR  

              10:42

    

     

     

2 .13

  

2019

TEMP

    

     

     

    24C

  

ALARM--P

    

     

     

  

dISP

YES / AIR

    

     

               

  

dISP

NO / MODE

    

     

     

  

dISP

Содержание GasWatch 3
































































































Отзывы:

Нет отзывов