Quick Start Guide
Before operating the unit, please read this manual thoroughly and
keep this for future reference.
Please access our website and download necessary IPAdminTool first:
http://www.rivatech.de/en/downloads/software
SV3502(73NIR)04-2017-A
About the manual
This manual provides the brief instructions for the installation
and the basic configuration of your IP device. For more
information about the installation and configuration, refer to the
device’s installation guide and the web page user’s manual.
Part names and functions
Please check the name and the position of each part by
referring to the following images.
Terminal Connector:
Connect the provided terminal block for cable
connection of digital input/output, audio input/output, and DC12V
power.
Ethernet Connector:
Connect an RJ-45 LAN cable for 10/100 Base-T
Ethernet (PoE supported).
Reset Button:
Press the button either for the restart or the factory
default of the device. For
restart
,
1.
press the button
only for 2
seconds while
the device is powered on.
2.
Wait for the system
to reboot. For
factory default
,
1.
press the button for 10 second while
the device is powered on.
2.
Wait for the system to reboot.
mircoSD/SDHC Card Slot:
Insert a card up to 32GB.
Class 4 or the above is recommended for HD recording.
Installation
There is only one type of mounting explained in this manual. Refer
to the device’s installation guide for more various mounting types.
CAUTION
To prevent from damage, place the camera on a stable and non-
vibrating surface.
Adjusting angle of camera
NOTE
Tighten the tilt stopper after the tilt angle is confirmed.
CAUTION
Refrain from continuous rotation of the camera gimbal to a single
direction as it is linked with an internal cable.
Adjusting zoom and focus
The zoom and focus can be managed via the camera’s web page
(path: Setup > Video & Audio > Zoom/Focus). Thus, it is necessary to
connect the device on a network in advance to the zoom and focus
adjustment.
- Adjust zoom/focus by clicking the arrow buttons: The buttons
move the lens more extensively than the buttons
.
- If you want to set the focus automatically, click
One Click Focus
.
- If the focus point is considered misaligned, reset it to a zero point
by clicking
Calibrate
.
C. For the horizontal rotation of the
lens, rotate the inner liner clockwise
or counter-clockwise.
(The rotating range is limited to 358 degrees.)
inner liner
B. To tilt, tilt the gimbal by referring to
the image on the left.
A. To pan, rotate the gimbal bracket
clockwise or counter-clockwise.
(The panning range is limited to 358 degrees.)
gimbal
bracket
gimbal
tilt
stopper
M4x30 screw
DO
DI
1
1
C
C
+
DC12V
ETHERNET
RESET
MICRO
SD
DO
DI
1
1
C
C
+
DC12V
ETHERNET
RESET
MICRO
SD
ETHERNET
WIRE
2 turns
micro
SD/SDHC card slot
Reserved
DO DI AUDIO DC
12V
X X C 1 C 1 O
I - +
Ethernet
connector
Reset
button
Terminal connector
1)
Place the installation template included in the package on a
desired installation surface.
2)
Drill three holes for the plastic anchors based on the template
paper, and insert the plastic anchors into the holes. (In case you
need to connect the cables through the mounting surface, drill an
additional hole to pass the cables based on the size of the cable
entry hole.)
3)
Attach the provided silicon waterproof band to the bottom of
the camera body for the prevention of water permeation.
4)
Open the dome cover with the provided L wrench (3mm),
install the provided ferrite core to the LAN cable by referring to
the squared image on the bottom left of this page, and connect
all the necessary cables dropped from the ceiling to the
corresponding connectors on the camera.
5)
Prepare the screws (M4x30) with the O-rings inserted. Then,
place the camera body to match the alignment holes with the
corresponding
plastic anchors, insert the O-ring inserted screws
into the screw holes on the camera body, and tighten them into
the plastic anchors with a screw driver.
6)
Adjust the angle of the camera. Refer to the section,
Adjusting angle of camera
for more information.
7)
Adjust zoom and focus of the camera. Refer to
Adjusting
zoom and focus
for more information.
8)
Reattach the dome cover to the camera body by aligning the
alignment marks on both the dome cover and the camera body.
9)
Once the dome cover and the camera body are properly
aligned, tighten the bolts on the dome cover into the camera
body with the provided L wrench for the firm attachment. Then,
remove the protection film from the dome cover.
DO
DI
1
1
C
C
+
DC12V
ETHERNET
RESET
MICRO
SD
DO
DI
1
1
C
C
+
DC12V
ETHERNET
RESET
MICRO
SD
ETHERNET
WIRE
DO
DI
1
1
C
C
+
DC12V
ETHERNET
RESET
MICRO
SD
DO
DI
1
1
C
C
+
DC12V
ETHERNET
RESET
MICRO
SD
ETHERNET
WIRE
DO
DI
1
1
C
C
+
DC12V
ETHERNET
RESET
MICRO
SD
DO
DI
1
1
C
C
+
DC12V
ETHERNET
RESET
MICRO
SD
ETHERNET
WIRE
