INSTALLATION
Anchor to Concrete*
The SpanGuard Mesh Safety Barrier requires a minimum
concrete thickness of 4in [102mm] to provide proper unit
support
10.00in
254mm
23.42in
595mm
CLEAR OPENING WIDTH
B
A
1
Titan HD Concrete Anchor Installation Instructions
Tools Required:
Hammer Drill with ¾” x 8” Concrete Drill Bit
Impact Wrench with 1‑1/8” Impact Socket
Installation:
Drill a ¾” Diameter hole in the concrete. The hole should be drilled a minimum of 8” deep
or completely through the concrete
Using a drill bit that is too small or excessively
worn will make it very hard to install the
anchor. Using a drill bit that is too large will reduce the anchors load capacity.
Use compressed air to blow the concrete dust out of the hole. If this is not done, you may
not be able to tighten the anchor completely
Using the Impact wrench and 1‑1/8” socket, install the anchor through the base plate and
into the hole you drilled into the concrete
Securely tighten all anchors with the impact wrench. Make sure the hex washer head is in
contact with the base plate.
Position the safety barrier in its
intended position Use the base plate
of the post (B) as a template and
drill the appropriate size hole in the
concrete per anchor being used The
hole should be drilled a minimum of
1in [25mm] deeper than the length of
the anchor or completely through the
concrete
Using a drill bit that is too:
–
small or excessively worn will
make it very hard to install the
anchor
–
large will reduce the anchor load
capacity
2
Titan HD Concrete Anchor Installation Instructions
Tools Required:
Hammer Drill with ¾” x 8” Concrete Drill Bit
Impact Wrench with 1‑1/8” Impact Socket
Installation:
Drill a ¾” Diameter hole in the concrete. The hole should be drilled a minimum of 8” deep
or completely through the concrete
Using a drill bit that is too small or excessively
worn will make it very hard to install the
anchor. Using a drill bit that is too large will reduce the anchors load capacity.
Use compressed air to blow the concrete dust out of the hole. If this is not done, you may
not be able to tighten the anchor completely
Using the Impact wrench and 1‑1/8” socket, install the anchor through the base plate and
into the hole you drilled into the concrete
Securely tighten all anchors with the impact wrench. Make sure the hex washer head is in
contact with the base plate.
Use compressed air to clean the
drilled hole so you can tighten the
anchor completely
3
Titan HD Concrete Anchor Installation Instructions
Tools Required:
Hammer Drill with ¾” x 8” Concrete Drill Bit
Impact Wrench with 1‑1/8” Impact Socket
Installation:
Drill a ¾” Diameter hole in the concrete. The hole should be drilled a minimum of 8” deep
or completely through the concrete
Using a drill bit that is too small or excessively
worn will make it very hard to install the
anchor. Using a drill bit that is too large will reduce the anchors load capacity.
Use compressed air to blow the concrete dust out of the hole. If this is not done, you may
not be able to tighten the anchor completely
Using the Impact wrench and 1‑1/8” socket, install the anchor through the base plate and
into the hole you drilled into the concrete
Securely tighten all anchors with the impact wrench. Make sure the hex washer head is in
contact with the base plate.
Use an impact wrench and 3/4in
socket to install the (provided)
3/4in x 7in Titan HD
®
concrete
anchors (A) through base plate
and into the holes drilled into the
concrete
4
Titan HD Concrete Anchor Installation Instructions
Tools Required:
Hammer Drill with ¾” x 8” Concrete Drill Bit
Impact Wrench with 1‑1/8” Impact Socket
Installation:
Drill a ¾” Diameter hole in the concrete. The hole should be drilled a minimum of 8” deep
or completely through the concrete
Using a drill bit that is too small or excessively
worn will make it very hard to install the
anchor. Using a drill bit that is too large will reduce the anchors load capacity.
Use compressed air to blow the concrete dust out of the hole. If this is not done, you may
not be able to tighten the anchor completely
Using the Impact wrench and 1‑1/8” socket, install the anchor through the base plate and
into the hole you drilled into the concrete
Securely tighten all anchors with the impact wrench. Make sure the hex washer head is in
contact with the base plate.
Securely tighten all anchors to
65ft‑lbs
[88Nm] with the impact
wrench. Make sure the hex washer
head is in contact with the base plate.
5 Repeat this process for all of the concrete anchors on
the post
*Image credits: Titen HD Concrete Anchor instructions
(strongtiecom)
Figure 4
Rite‑Hite
®
Installation/Service/Owner's Manual
SpanGuard
®
Mesh Safety Barrier
Publication:
AMEN00136 2019-11-22
5
