RITE-HITE SlideAir Скачать руководство пользователя страница 3

Страница: 3 / 24

Rite‑Hite

Installation/Service/Owner's Manual

SlideAir™ Pneumatic Safety Curtain

Publication:

AMEN00119 2020-07-06

SAFETY
Safety Identifications

DANGER

Indicates a hazardous situation which, if not

avoided, will result in death or serious injury.
Indique une situation dangereuse qui, si elle n’est

pas évitée, peut entraîner la mort ou de graves

blessures.

WARNING/AVERTISSEMENT

Indicates a hazardous situation which, if not

avoided, could result in death or serious injury.
Indique une situation dangereuse qui, si elle n’est

pas évitée, peut entraîner la mort ou des

blessures graves.

CAUTION/ATTENTION

Indicates a hazardous situation which, if not

avoided, could result in minor or moderate injury.
Indique une situation dangereuse qui, si elle n’est

pas évitée, peut entraîner des blessures légères à

modérées.

NOTICE

Indicates a situation which can cause damage to the

equipment, personal property and/or the environment,

or cause the equipment to operate improperly

NOTE:

A note is used to inform you of important

installation, operation, or maintenance information

Lockout Procedure

Barricade work area and post safety warnings
Power supply and control must:
• Be disconnected or locked in OFF position

using a lockout device approved by local

codes

• Have signage that;

−

Clearly states repairs are being made

− Identifies person responsible for lockout condition.

NOTE:

Only this person should be able to remove

warnings and lockout device

−

Withstands environmental conditions (weather,

wet, and damp, etc) and remains readable

190820

Содержание SlideAir

























Результаты поиска

Содержание SlideAir

Отзывы:

Похожие инструкции для SlideAir

Бренды по названию

Популярные бренды

RITE-HITE SlideAir, Инструкция по установке/обслуживанию/эксплуатации

Результаты поиска

Содержание SlideAir

Отзывы:

Похожие инструкции для SlideAir

Бренды по названию

Популярные бренды