RITE-HITE RHH-5000 Скачать руководство пользователя страница 12

Страница: 12 / 40

LEVELER ADJUSTMENTS

LIP STOP BOLT

The lip stop bolt adjusts the position of the lip when the leveler

is stored to allow the lip to be centered on lip supports when

stored.

NOTE:

Lip stop bolt will need to be adjusted on longer lips to

allow lip to be centered in the lip keepers.

ARTD CAM ADJUSTMENT

NOTE:

Before continuing be sure the lip stop bolt is properly

adjusted. See figure 11.

1. Raise leveler and install a strut securely behind the header or

mini-header to allow the lip to hang pendant and rest against the

lip stop bolt.

2. Adjust ARTD Cam.
a. Adjust collars so the front edge of ARTD cam is 1/16” behind the

centerline of the ARTD limit switch. See figure 12.

b. Tighten front collar while holding the 1/16” adjustment.
c. Push the rear collar forward as much as possible and tighten.

ARTD cam assembly should rotate freely.

3. Run the leveler to test the adjustment. Verify that the lip falls a

minimum of 4” before ARTD is initiated. If not, move the cam

forward slightly.

NOTE:

It is not recommended to position the ARTD cam in front

of the ARTD limit switch centerline.

7/8”

Ref.

1/16”

ARTD

Limit Switch

Rear

Collar

ARTD Cam

Front Washer

Front Collar

NOTE:

There Should Be A Small Amount Of Free Movement

Between The ARTD Cam And The Rear Collar When

The Rear Collar Is Pushed Against The ARTD Cam.

This Edge Of Cam

To Be Positioned

1/16” Behind The

Center Of Roller

As Shown.

ARTD Cam Adjustment Detail

(Shown With Lip Pendant And Lip Stop Bolt Adjusted)

FIGURE 12 - ARTD LIMIT SWITCH

•

DO NOT operate leveler with anyone standing on or in

front of the lip.

•

NEVER go under the hydraulic leveler platform or lip without

installing the Maintenance Support.

•

Make sure that the leveler power is locked out and tagged out

according to OSHA regulations and approved local codes.

Lip In

Keepers

Lip

Stop Bolt

FIGURE 11 - LIP STOP BOLT

•

Adjustments to be completed by trained technician only.

RHH-5000 High Capacity Dock Leveler

Owner’s Manual

Rite-Hite

Publication:

AMEN00206 2020-02-04

Содержание RHH-5000









































Результаты поиска

Содержание RHH-5000

Отзывы:

Похожие инструкции для RHH-5000

Бренды по названию

Популярные бренды

RITE-HITE RHH-5000, Руководство пользователя

Результаты поиска

Содержание RHH-5000

Отзывы:

Похожие инструкции для RHH-5000

Бренды по названию

Популярные бренды