Riso MZ1070 Скачать руководство пользователя

Страница: 120 / 150

[ 16-86 ]

MZ870 / MZ890 / MZ1070 / MZ1090

(Revision 0.9)

PANEL MESSAGE

Error type

C01 [Ink cartridge replacement] (Drum No. 1)

Panel display

C01-***

No Ink in Print Cylinder 1

Replace Ink Cartridge

Error reset

method

First ink cartridge set SW: OFF -> ON << Install a new ink cartridge to cancel the error. >>

Or first print drum safety SW: OFF, first print drum connection signal: OFF, and first print drum lock sensor:

OFF << Pull out the print drum to cancel the error. >>

Error point

Error detecting condition

512

The ink sensor does not switch ON when the inking operation is conducted for the set time (inkless).

563

The remaining volume information in the ink tag reached the maximum value.

574

Inkless error was generated 5 times for the same ink cartridge.

Error type

C02 [Master roll replacement]

Panel display

C02-***

No Master

Replace Master Roll

Error reset

method

Master-making unit sensor: OFF -> ON << Open and close the master-making unit to cancel the error. >>

Error point

Error detecting condition

200

The 10-ms-interval master end check detected 2 consecutive times during the master transport.

240

The remaining volume information in the master tag reached the maximum value.

253

[No-master] error was generated twice for the same master.

Error type

C03 [ Master disposal box full (Drum No. 1)

Panel display

C03-***

Master Disposal Box 1 is Full

Empty Master Disposal Box

Error reset

method

Switch OFF the first master disposal box sensor OFF, then turn ON after waiting at least 5 seconds.

Error point

Error detecting condition

308

After the master compression motor activates in the compressing direction, the compression detection

switches ON before the FG count exceeds the specified volume.

311

The master compression software counter reached the full detection set count.

Error type

C04 [No-paper error]

Panel display

C04-***

Add Paper

Error reset

method

The paper detection sensor is ON.

Error point

Error detecting condition

402

The paper detection sensor is OFF.

4. Consumable errors (C**)

Содержание MZ1070























































































































































Результаты поиска

Содержание MZ1070

Отзывы:

Похожие инструкции для MZ1070

Бренды по названию

Популярные бренды

Riso MZ1070, Техническое руководство

Результаты поиска

Содержание MZ1070

Отзывы:

Похожие инструкции для MZ1070

Бренды по названию

Популярные бренды