background image

Rinnai 

Split AC IM

WARNING

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

.

Always comply with the following precautions to avoid dangerous situations and to ensure 

optimum performance.
Failure to carefully read and follow all instructions in this manual can result in equipment 

malfunction, property damage, personal injury and/or death.

DANGER:

  Indicates an imminently hazardous situation which, if not avoided, will result in 

personal injury or death.

WARNINGS:

  Indicates a potentially hazardous situation which, if not avoided, could result in 

personal injury or death.

CAUTIONS:

  Indicates a potentially hazardous situation which, if not avoided, could result in 

minor or moderate injury or damage to the appliance. It may also be used to alert against unsafe 

practices.

WARNING

REGULATORY

This appliance shall be installed in accordance with:

Manufacturer’s Installation Instructions.
Current  AS/NZS 3000, AS/NZS 5141.
Local Regulations and Municipal Building Codes including local OH&S requirements.

This appliance must be installed, maintained and removed 

ONLY

 by an Authorised Person.

For continued safety of this appliance it must be installed and maintained in accordance with the 

manufacturers instructions.
This appliance uses R32 refrigerant.
This appliance is heavy, use 2 people or mechanical lifting device. Improper lifting may result in 

serious injury.
Take care when opening or unpacking this appliance. Failure to do so may result in serious injury 

or product failure.

DO NOT

 modify the electrical wiring of this appliance. If the control power wiring is damaged 

or deteriorated then it must be replaced by an authorised person. Failure to do so may result in 

electric shock, fire, serious injury or product failure.

DO NOT

 install the air conditioner on an unstable or non level surface or where there may be a 

danger of it falling. It may result in death, serious injury, or product failure.

DO NOT 

install the outdoor unit where noise may cause nuisance.

DO NOT 

install the outdoor unit where it will be exposed to sea wind (salt spray) as this will 

reduce durability.

IMPORTANT

MANDATORY INSPECTION PRIOR TO INSTALLATION

Immediately report any damage or discrepancies to the Supplier of the appliance. This 

appliance was inspected and tested at the time of manufacture and packaging, and released for 

transportation without known damage. Upon receipt, inspect the exterior for evidence of rough 

handling in shipment. Ensure that the appliance is labelled correctly for the gas and electrical 

supply, and/or other services it is intended to be connected to.
For safety and warranty purposes, appliances that may be damaged or incorrect 

MUST NOT

 be 

installed or operated under any circumstances. Installation of damaged or incorrect appliances 

may contravene local government regulations. Rinnai disclaims any liability or responsibility 

whatsoever in relation to the installation or operation of damaged or incorrect appliances.

WARNINGS AND IMPORTANT INFORMATION

Содержание HINRJ25B

















Отзывы: