Rinnai Brivis DINLU10Z7 Скачать руководство пользователя

Страница: 4 / 28

1.3 Codes / Regulations

Brivis ICE units must be installed, serviced or repaired in accordance with these instructions and related regulations, codes,

standards, and authorities. These include but may not be limited to:

•

Ozone Protection and Synthetic Greenhouse Gas Management Regulations 1995

•

AS/ NZS 1677.2 - Australian Standard, Refrigeration systems, safety requirements for fixed applications

•

AS 4211.3 Gas recovery or combined recovery and recycling equipment

•

HB 276-2004 : A Guide to Good Practice for Energy Efficient Installation of Residential Heating, Cooling & Air

Conditioning Plant & Equipment

•

AS 4254 - Ductwork for air-handling systems in buildings

•

Local Electricity Authority

•

Local Building Regulations

•

Environment Authorities

•

Building Code of Australia (BCA)

•

Brivis “SuperSizeGuide”

It is recommended the Brivis “SuperSizeGuide” be followed in estimating cooling requirements and for system design that

will result in efficient installation and provide a higher level of comfort and economical operation.

Brivis assumes no responsibility for equipment installed in violation of any code or regulations and these installation

instructions.

2.0 Components

Upon receiving units, inspect for damage and ensure appliances match your order. In the event of damage, or incorrect delivery, notify

supplier immediately. Brivis accepts no responsibility for installation of damaged or incorrect units.

2.1 Indoor Unit (Cooling Coil)

Remove packaging from unit and any protective foam packing from coils and pipes. Indoor units are shipped with a holding

charge of dry nitrogen. Check to confirm the holding charge. For lifting details refer to the General Arrangement drawings.

•

Brivis Inverter ICE indoor units shall be installed only downstream of a heater

•

Brivis Inverter ICE is not designed for installation on a marine craft, houseboat, or any similar environment.

Fig. 1a – DINXU Indoor Cooling Coil

P-Trap

Assembly

Access

Plate

Power Cord &

Plug

Electric Box

Содержание Brivis DINLU10Z7





























Результаты поиска

Содержание Brivis DINLU10Z7

Отзывы:

Похожие инструкции для Brivis DINLU10Z7

Бренды по названию

Популярные бренды

Rinnai Brivis DINLU10Z7, Руководство по установке

Результаты поиска

Содержание Brivis DINLU10Z7

Отзывы:

Похожие инструкции для Brivis DINLU10Z7

Бренды по названию

Популярные бренды