background image

32

Requirements and conditions

Sizing of the battery flue system

Each individual heat generator is approved for the 

connection to a smoke duct for expulsion outside the 

combustion products, through an attack of Ø100mm.
In the case in which the connection in hydraulic cascade 

is made of the appliances, it is possible to evacuate the 

products of combustion with a single chimney of certain 

efficiency for each appliance, or provide for installation of 

a single flue gas collector of certain efficiency for all the 

appliances. In case the connection in cascade of several 

units to the same evacuation duct, is it is necessary to place 

one on each exhaust terminal clapet type valve (smoke 

non-return valve), to prevent the return of the fumes inside 

the boiler if this does not is in operation.
The individual modules must be connected to each other via 

a suitably sized flue gas exhaust manifold.
Rinnai supplies manifolds appropriately upon request sized. 

This type of installation provides only one expulsion of 

fumes, while the air intake is made in the environment.
As required by legislation, the sizing of flues (single or 

collective) falls within the scope responsibility of the 

designer or installer, who they must comply with specific 

technical regulations applicable.
Below is an indicative table of lengths maximum, depending 

on the diameters used.

B

A

M

R

G

M

R

G

Model

Number of 

appliances

Manifold 

diameter

Maximum 

length (A + B) 

equivalent

Horizontal 

section 

diameter A

Smoke 

expulsion 

chimney 

diameter B

Equivalent 

pressure drop 

90 ° curve

Equivalent 

pressure drop 

45 ° curve

mm

m

mm

mm

m

m

aiM 65

2

160

20

160

160

7

2

3

160

20

160

160

3

2

4

160

20

160

200

3

2

aiM 85

2

160

20

160

160

7

2

3

160

20

160

160

3

2

4

160

20

160

200

3

2

aiM 115

2

160

20

200

200

7

2

3

160

20

200

200

3

2

4

160

20

200

300

3

2

aiM 150

2

200

20

200

200

2

2

3

200

20

200

315

1

1

4

200

20

250

400

1

1

Содержание aiM 115



































































Отзывы: