background image

 

 

31 

 

9.MEASURES AT AN ABNORMAL CASE 

 
9-1.Trouble alarm 
 

Flashing of PW/TR light 

・When PW/TR light is flashing, it is the condition that the following trouble may be caused.  

Research its cause and take an appropriate action. 

・The output from the unit at trouble shall be as  follows. 

4~20mA output 

: Fixed at 0.5mA 

 

Trouble alarm contact 

: Relay contact is activated. 

 

LED display 

Trouble content 

Main cause 

E-00 

System trouble 

Memory trouble in the unit. 

E-01 

Connection trouble 
of detection head 

Detector head disconnection, sensor disconnection, 
sensor cable disconnection. 

 
 
9-2.Counteraction at trouble alarm 
 

When any trouble was found on this unit and detector head, contact our nearest agent or RIKEN KEIKI. 

 
 
9-3.Before it is thought to be trouble 
 

It may be originated from disconnection and short circuit between units. 

・Check the wirings including peripheral equipment as well as detector head. 
・Re-check the detection system and contact our nearest agent or  RIKEN KEIKI. 

 

There is the case of electrical line trouble such as shut-off of power. 

・This will be treated by the re-check of stand-by battery, electrical line filter, insulation transformer 

etc or those addition. 

 
 
9-4.Trouble shooting 
 
(1) PW/TR light does not illuminate 

<Cause and action> 

・Is it OK with power cable connection? 

Connect power cable. 

・Is fuse disconnected? 

Search the cause of disconnection and replace it after making counter-measures. 

・Is power voltage normal? 

Supply the rating power voltage. 

・Is this power switch turned on? 

Make power switch ON. 

 
(2) Abnormal performance 

<Cause and action> 

・Sudden surge noise can be considered.    When recover it, turn off the power and turn on the power 

again for re-start of operation. 

When such takes place oftentimes, take an appropriate action for noise. 

 
(3) No calibration available 

<Cause and action> 

・Is the calibration gas concentration correct? 

Prepare the appropriate calibration gas. 

・There is the possibility for sensor sensitivity drop. 

The sensor replacement is required. 

Содержание OX-591





































Отзывы: