background image

 

 

12 

4-3.Installation place 
 

 
 
 
 
    Keep  away  the  system  from  direct  sun  drought  or  where  the  temperature  of  the  system  is 

drastically  changed.    If  installed, inside  the unit  will be  built  up condensation and does not  follow 
the drastic temperature change. 

 
 
 

The system consists of fine electronics parts. 

Install them where to be stable not to crush or fall down. 

 
 
     

Keep the system from the equipment which may give a high frequency in the surroundings and install 

it. 
・Do not put the system jointly each.   
・Do not wire the cable in parallel nor take access. 


 
 

Do not install and make gas detection at the place where the sample gas is deposited. 

 
 
 
 

This unit is required to make maintenance regularly. 
Then, do not install at the place where there is danger at maintenance time. 

 
 
 

When required to stop the system at maintenance time, unable to maintain if not remove a part of 
system or unable to detach the case due to the pipe or rack etc. do not install such place. 

 
 
 

Be sure to ground when installing to the equipment. 

 

 
 
 

Do not install at places where direct sun drought or where the temperature is drastically changed. 

Do not install it where vibration or shocks may take place. 

Keep the system from the equipment which may generate the noise (Unit & cable). 

Do not install it where the detection gas is deposited around. 

Do  not install  at  the place  where  it is danger for maintenance  service such  as high voltage  cable, 
etc. 

Do not install it where it is unable to make maintenance. 

Equipment housing that grounding construction is not enough. 

CAUTION 

Содержание OX-591





































Отзывы: