Rigol DS70000 Series Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 43

Rigol DS70000 Series Скачать руководство пользователя страница 31

7. Set the signal generator output frequency to the maximum bandwidth frequency

of the oscilloscope. For the maximum bandwidth frequency of the oscilloscope,

refer to

.

8. Adjust the horizontal timebase of the oscilloscope.

9. Check the "AC.RMS" result list at the right section of the screen. Read and record

the data as Vout

max

.

10. Record the power meter reading P

max

, and convert the power to V according to

the following formula.

11. Calculate the test results by using the formula below:

12. The above result should be greater than -3 dB.

13. Repeat Step 3-12 according to the test record form and calculate the test results.

5.4.4

Test Record Form

Model

Limit

CH1

CH2

CH3

CH4

DS70304 (3 GHz)

-3 dB

DS70504 (5 GHz)

-3 dB

5.5

Timebase Accuracy Test

5.5.1

Specification

Timebase Accuracy

[1]

Specification

±(0.5 ppm + 1 ppm

[2]

/year × Number of Years that the

Instrument Has Been Used

[3]

)

NOTE

[1]: Typical.

[2]: Clock Drift.

[3]: For the number of years that the instrument has been used, please calculate according to
the date in the verification certificate provided when the instrument leaves factory.

Performance Verification Test

Copyright ©RIGOL TECHNOLOGIES CO., LTD. All rights reserved.

DS70000 Performance Verification

25

«
...
29
30
31
32
33
...
»

Содержание DS70000 Series












































Отзывы:

Нет отзывов