Rigol DS70000 Series Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 43

Rigol DS70000 Series Скачать руководство пользователя страница 17

5

Performance Verification Test

This chapter takes DS70504 as an example to illustrate the performance verification
test methods and procedures of DS70000 series digital oscilloscope. The
recommended test devices in this manual is shown below. You can also use other
devices that fulfill the "Specification" in the following table.

Table 5.1 Test Devices

Device

Specification

Recommended Model

DC Votage
Source

3 mV to 4 V, ±0.1% accuracy

Fluke 9500B

RF Signal
Generator

10 kHz to 5 GHz

RIGOL DSG3000B Series RF
Signal Generator (with the
OCXO-B08 option)

Power Meter

1 MHz to 5 GHz, ±3% accuracy

-

Power Sensor

1 MHz to 5 GHz, ±3% accuracy

-

Power Splitter

Full-scale accuracy ≤ 0.2 dB

-

TIP

1. Make sure that the oscilloscope passes the self-test and self-calibration is performed before

executing the performance verification tests.

2. Make sure that the oscilloscope has been warmed up for at least 30 minutes before

executing any of the following tests.

3. Please reset the instrument to the factory setting before or after executing any of the

following tests.

5.1

Impedance Test

5.1.1

Specification

Input Impedance

Analog Channel

1 MΩ: 0.99 MΩ to 1.01 MΩ
50 Ω: 48.75 Ω to 51.25 Ω

Performance Verification Test

Copyright ©RIGOL TECHNOLOGIES CO., LTD. All rights reserved.

DS70000 Performance Verification

11

«
...
15
16
17
18
19
...
»

Содержание DS70000 Series












































Отзывы:

Нет отзывов