Rigol DS4000E Series Скачать руководство пользователя страница 155

Страница: 155 / 278

Chapter 2 Command System

RIGOL

DS4000E Programming Guide

2-143

:MEASure:RECover

Syntax

:MEASure:RECover <item>

Description

Recovers the measurement items that have been cleared.

Parameter

Name

Type

Range

Default

<item>

Discrete

{ITEM1|ITEM2|ITEM3|ITEM4|ITEM5|ALL}

Remarks

After you have recovered the measurement items that have been cleared, you can also use

the :MEASure:CLEar command to clear them again.

:MEASure:RDELay

Syntax 1

:MEASure:RDELay [<chanA>,<chanB>]

Description 1

Measures the delay (rising edge-rising edge) between the two specified source channels.

Syntax 2

:MEASure:RDELay? [<chanA>,<chanB>]

Description 2

Measures and queries the delay (rising edge-rising edge) between the two specified source channels. The

default unit is s.

Parameter

Name

Type

Range

Default

<chanA>

Discrete

{CHANnel1|CHANnel2|CHANnel3|CHANnel4}

<chanB>

Discrete

{CHANnel1|CHANnel2|CHANnel3|CHANnel4}

Remarks



Before making measurements, turn on the channels to be measured.



When [<chanA>,<chanB>] is omitted, this command will be applied to Source A (refer to

the :MEASure:SETup:DSA command) and Source B (refer to the :MEASure:SETup:DSB command) of

delay measurement currently set by default.

Return Format

The query returns the measurement results in scientific notation. When the measurement results are

invalid, the query returns 9.9e37.

Содержание DS4000E Series























































































































































































































































































Результаты поиска

Содержание DS4000E Series

Отзывы:

Бренды по названию

Популярные бренды

Rigol DS4000E Series, Руководство по программированию

Результаты поиска

Содержание DS4000E Series

Отзывы:

Бренды по названию

Популярные бренды