Rigol DS2000E Series Скачать руководство пользователя страница 240 | Manualshive

Страница: 240 / 283

Rigol DS2000E Series Скачать руководство пользователя страница 240

RIGOL

Chapter 13 System Function Setting

DS2000E User’s Guide

13-2

Remote Interface Configuration

DS2000E can communicate with PC via LAN, USB, or GPIB (with the USB-GPIB
interface converter provided by

RIGOL

) bus. Please refer to the introduction below

to configure the corresponding interface before using the remote interfaces.

LAN Setting

Press Utility



IO Setting



LAN Set to turn on the LAN setting interface. You

can view the network connection status and configure the network parameters.

Figure 13-1 LAN Setting Interface

Network Status

Connect the oscilloscope to your local area network using the network cable. The
network interface of the oscilloscope is on the rear panel. The oscilloscope will give
different prompts according to the current network connection status.



Net Config Success!



Acquire IP…



IP Conflict!



Unconnected!



DHCP Fail!



Read Status Fail!

Network Status

Current IP

Config. Type

MAC Address

VISA Address

IP Config. Type

Status

«
...
238
239
240
241
242
...
»

Содержание DS2000E Series




























































































































































































































































































Отзывы:

Нет отзывов