Rigol DS2000E Series Скачать руководство пользователя страница 206

Страница: 206 / 283

RIGOL

Chapter 10 Waveform Record

10-8

DS2000E User’s Guide

Waveform Analysis

This function is used to analyze the recorded waveform. Press Utility



Record



Mode and use

to select "Analyze" to open the waveform analysis menu. At this

point, the screen is divided into two display areas as shown in the figure below.

Figure 10-3 Waveform Analysis

Please refer to the following explanations to set the waveform analysis parameters.

1.

Analyze
Press Analyze to select the desired analysis mode.



Trace: perform analysis on the basis of the templet selected by users. For
the detailed information, refer to "Analysis Based on Trace".



Pass/Fail: perform analysis on the basis of the Pass/Fail mask created by

users. For the detailed information, refer to "Analysis Based on

Pass/Fail Mask".

Source
Press Source to select the channel (CH1 or CH2) to be analyzed.
Note: Only currently enabled channels can be selected.

Settings and Results Templet Display Current Frame

Содержание DS2000E Series




























































































































































































































































































Результаты поиска

Содержание DS2000E Series

Отзывы:

Rigol DS2000E Series, Руководство пользователя, Страница: 206 / 283

Результаты поиска

Содержание DS2000E Series

Отзывы: