Rigol DS 5000C Скачать руководство пользователя страница 119

Страница: 119 / 122

RIGOL

Appendix C: General Care and Cleaning

General Care

Do not store or leave the instrument in where the LCD display will be exposed to
direct sunlight for long periods of time.

CAUTION:

To avoid damage to the instrument or probes, do not expose

them to sprays, liquids, or solvents.

Cleaning

If this instrument requires cleaning, disconnect it from all power sources and clean it
with a mild detergent and water. Make sure the instrument is completely dry before
reconnecting it to a power source.

To clean the exterior surface, perform the following steps:

Remove loose dust on the outside of the instrument and probes with a lint- free

cloth. Take care to avoid scratching the clear plastic display filter.

Use a soft cloth dampened with water to clean the instrument.

NOTICE:

To avoid damage to the surface of the instrument or probes, do not use

any abrasive or chemical cleaning agents.

6-7

User Manual for DS5000 Series

Содержание DS 5000C



























































































































Результаты поиска

Содержание DS 5000C

Отзывы:

Rigol DS 5000C, Руководство пользователя, Страница: 119 / 122

Результаты поиска

Содержание DS 5000C

Отзывы: