Rigol DG800 Series Скачать руководство пользователя

Страница: 16 / 148

RIGOL

Chapter 1 Quick Guide

1-2

DG800 User's Guide

General Inspection

．

Inspect the packaging

If the packaging has been damaged, do not dispose the damaged packaging or

cushioning materials until the shipment has been checked for completeness and

has passed both electrical and mechanical tests.

The consigner or carrier shall be liable for the damage to the instrument

resulting from shipment.

RIGOL

would not be responsible for free

maintenance/rework or replacement of the instrument.

．

Inspect the instrument

In case of any mechanical damage, missing parts, or failure in passing the

electrical and mechanical tests, contact your

RIGOL

sales representative.

．

Check the accessories

Please check the accessories according to the packing lists. If the accessories

are damaged or incomplete, please contact your

RIGOL

sales representative.

Содержание DG800 Series





















































































































































Результаты поиска

Содержание DG800 Series

Отзывы:

Похожие инструкции для DG800 Series

Бренды по названию

Популярные бренды

Rigol DG800 Series, Руководство пользователя

Результаты поиска

Содержание DG800 Series

Отзывы:

Похожие инструкции для DG800 Series

Бренды по названию

Популярные бренды