Rigaku MiniFlex 600 Скачать руководство пользователя страница 9

Страница: 9 / 111

MiniFlex 600: Benchtop X-ray Diffractometer

Configuration

Standard Configuration

X-ray generator (XG):

Power source for X-ray generation

Tube shield:

X-ray tube holder

Goniometer:

Measurement unit at 2

diffraction angle

Detector (SC):

Scintillation counter

Counting control circuit (ECP):

Counting and measurement controller

Radiation enclosure:

Enclosure cabinet of the main unit that
provides protection from radiation

Flow rate detector:

For monitoring flow rate of cooling water.

X-ray tube

LAN cable
Computer (for Japanese market only):

PC, Printer

An X-ray tube and a computer (PC, etc.) are required to use this equipment.
These components may be required to be prepared by the user or distributor due
to warranty issues.

If an auto-transformer or an external heat exchanger is required, contact the sales
representative who you purchased the instrument from.

Содержание MiniFlex 600
















































































































Результаты поиска

Содержание MiniFlex 600

Отзывы:

Похожие инструкции для MiniFlex 600

Бренды по названию

Популярные бренды

Rigaku MiniFlex 600, Инструкция по эксплуатации

Результаты поиска

Содержание MiniFlex 600

Отзывы:

Похожие инструкции для MiniFlex 600

Бренды по названию

Популярные бренды