Rigaku MFM65S2RFFFLFL Скачать руководство пользователя страница 26

Страница: 26 / 102

−

ME12058B

Operation Section

3.6 Explanation of Software

Navigation Buttons

Contents

Daily operation using recipes
Loadport1

Executes recipes for load port 1.

Loadport2

Executes recipes for load port 2.

Job

Chart

Displays graphs on the main window.

Enables manual operation for maintenance purposes.
EFEM

Loads or unloads a wafer from the carrier to the sample stage.

Optics1

Sets x-ray power for optics 1.

System

Optics2

Sets x-ray power for optics 2.

Constructs recipes to execute jobs.
Process Recipe

Creates and edits process recipes by combining analysis recipe
and wafer recipe.

Analysis Recipe

Creates and edits analysis recipes at an arbitrary point on wafers.

Wafer Map

Creates and edits recipes for the mapping of points on
non-patterned wafers.

Recipes

Pattern Map

Creates and edits recipes for the mapping of points on patterned
wafers.

Displays recent LOGs.
Equipment Log

Displays the current equipment log on the main window.

Process Log

Displays the current process log on the main window.

Data Log

Alarm

Displays the current alarms and the history log of past alarms.

Sets the equipment parameters for the MFM65 system.
EFEM setting

Sets the equipment parameters for EFEM.

Optics Setting

Sets the equipment parameters for optics.

Setup

System Setup

Sets the system parameters.

Sets the equipment parameters for the MFM65 system.

Startup

Startup/Shutdown

Executes startup or shutdown of this equipment.

Displays the current alarm information and the history log of past alarms.
Alarm

Displays the current alarm information.

Alarms

Alarm Log

Displays the history log of past alarms.

Содержание MFM65S2RFFFLFL







































































































Результаты поиска

Содержание MFM65S2RFFFLFL

Отзывы:

Похожие инструкции для MFM65S2RFFFLFL

Бренды по названию

Популярные бренды

Rigaku MFM65S2RFFFLFL, Инструкция по эксплуатации

Результаты поиска

Содержание MFM65S2RFFFLFL

Отзывы:

Похожие инструкции для MFM65S2RFFFLFL

Бренды по названию

Популярные бренды