Rigaku MFM65S2RFFFLFL Скачать руководство пользователя страница 58

Страница: 58 / 102

−

ME12058B

Operation Section

9.8 XRF Measurement

Troubles

Causes and remedies

Analysis result is abnormal.

Check the selection of the recipe.

The measurement result
(thickness) is not calculated
after the measurement.

The constants of calibration curve are not registered.

The measurement result
(thickness) has no unit and
different digit number.

Enter the unit and the digit number in the XRF analysis
software.
Refer to the manual of the XRF analysis software.

After measuring the standard
sample, the data of the standard
sample cannot be loaded to the
XRF software of creating the
calibration curve.

When measuring the standard sample, enter “_C” strings to
the comment column.
Refer to the manual of the XRF analysis software.

After measuring the
standardization sample, the
data of the standardization
sample cannot be loaded to the
XRF standardization software.

When measuring the standardization sample, enter “_S”
strings to the comment column.
Refer to the manual of the XRF analysis software.

NOTE:

Contact the maintenance personnel for
checking the constants of calibration curve.

NOTE:

Contact the maintenance personnel for
checking the unit.

Содержание MFM65S2RFFFLFL







































































































Результаты поиска

Содержание MFM65S2RFFFLFL

Отзывы:

Похожие инструкции для MFM65S2RFFFLFL

Бренды по названию

Популярные бренды

Rigaku MFM65S2RFFFLFL, Инструкция по эксплуатации

Результаты поиска

Содержание MFM65S2RFFFLFL

Отзывы:

Похожие инструкции для MFM65S2RFFFLFL

Бренды по названию

Популярные бренды