WIRELESS SECURITY
PASSIVE INFRARED
WIDE-ANGLE DETECTOR
FOR OPEN AREAS
«
PYRONE-8-RK
»
Installation Guide
1 Product Overview
1.1 Wireless security passive infrared wide-angle detector «Pyrone-8-RK»,
(hereinafter, the detector) is designed for detecting intrusion into a protected
zone of closed or opened areas, with generation of alarm messages via wireless
two-way communication channel within the 433.05 – 434.79 MHz frequency range
by the «Rielta-Contact-R» protocol.
The detector is intended to operate as a component of any control
panel (hereinafter, CP), supporting the «Rielta-Contact-R» wireless two-way
communication protocol.
1.2 The detector radiated power does not exceed 10 mW.
1.3 The detector is powered from two power supply batteries, the main and
the backup one СR123A type, located inside the detector case and providing
normal operation of the detector for 3 years under normal climatic conditions, if
broadcasting period is not less than 30 sec.
1.4 The detector generates and transmits the following messages via radio
communication:
- «Norm» – under the other messages absence;
- «Alarm» – if the intrusion to the secured zone is detected;
- «Tamper» – upon the case tampering;
- «Main Power Supply Low-battery» – when the main battery supply voltage
drops up to 2.7
-0.1
V and lower;
- «Backup Power Supply Low-battery» – when the backup battery supply
voltage drops up to 2.7
-0.1
V and lower.
The detector provides the following indication:
- «Binding» – during the procedure of logging the detector in the CP;
- «Identification» – by receiving the relevant command from the CP.
1.5 The radio exchange is initiated by the detector with the periods: 10, 15,
30 sec, 1, 5, 10 min. The broadcast period is assigned in the process of the
detector adjustment. Tamper messages are transferred immediately.
1.6 The detector is provided with:
- three passive infrared channels for detection of the intrusion into protected
area;
- two-color (red and green) LED indication for displaying the detector state
and communication quality with CP in the place of installation;
- «SENS.HIGH» jumper for the detector sensitivity adjustment;
- «RESET» jumper for the detector changeover to the «Binding» mode;
- case tamper.
1.7 Two frequencies (main and reserve) are used for radio signals exchange
between the detector and CP.
Switching to a backup operating frequency in case of an imperfect interference
situation at the main one is realized automatically.
1.8 The detector has immunity to:
- pets up to 20 kg movement inside the detection zone;
- background illumination difference impact up to 20 000 lx;
- background illumination change at a rate of 5
о
С/min.
1.9 The Detector is resistant to the radio interference.
1.10 The detector design ensures it’s normal round-the-clock operation
outdoors.
2 Features
The detector has wide-angle detection zone.
The detection zone position can be aligned by means of the swivel bracket.
To ensure protection against an atmospherical condensation, the weather shield
is provided.
3 Specifications
Table 1
Parameter
Value
Maximum detection range
12 m
Permissible mounting height
2 … 3 m
Speed detection range
0.3 … 3 m/sec
Detection field-of-view angle in horizontal plane
90
о
Operating temperature
minus 40 … +50
о
С
Permissible relative humidity at 25
о
С
up to 100 %
Climatic design
moderately cold climate
IP rating
IP54
Dimensions, max
180 х 70 х 60 mm
Weight, max
0.2 kg
Battery life, not less
8 years
4 Scope of Delivery
The announcer scope of delivery is listed in Table 2.
Table 2
Name
QNT
Wireless security passive infrared wide-angle detector «Pyrone-8-RK»
Weather shield
Swivel Bracket
Antenna
Wall plug NAT 5x25 SORMAT
Screw 3-3x30.016
Power supply battery СR123A Plastic potting compound
Wireless security passive infrared wide-angle detector «Pyrone-8-RK».
Installation Guide
1 pc.
1 pc.
1 pc.
1 pc.
2 pcs.
2 pcs.
2 pcs.
1 copy
5 Design
The Detector (Figure 1) consists of base (1), PCB (3) and cover (6).
The PCB contains: two power supply battery CR123A holders (the main (5)
and the backup (4)), three infrared pyrodetectors (9), antenna (10) (supplied),
two-color LED indicator (11), tamper (12), jumper and contacts «SENS.HIGH» (13),
«RESET» contacts (14).
Swivel bracket (1) and weather shield (2) are available. The PCB is fixed on the
base by means of latch (15) and screw (8).
The cover (6) is fixed to the base (1) by four screws (7) with a sealing gasket.
Figure 2
6 Binding with the CP
6.1 The binding procedure is intended for logging of the Detector in the CP
and the transmission of service information to it. Prepare the CP for the Detector
binding in compliance with the CP Installation Guide.
6.2 Install first the backup power supply battery, and after the main one into
the holders, located on the PCB.
6.3 The LED indicator blinking green displays the detector readiness for the
binding procedure. In case the LED indicator does not blink, close the «Reset»
contacts for a short time period using any metal object.
6.4 After a successful binding with the CP, the LED indicator lights red for
2 seconds.
6.5 The detector operation in the «Binding» mode is limited to 100 sec. After
the time is up, the detector changes to the sleep mode. To resume the «Binding»
mode, the «RESET» contacts must be closed for a moment.
7 Choosing the Installation Place
The detection zone (see Figure 2) should reliably cover overall controlled
area. The detector should be installed at the height (2.3 ± 0.1) m. Take note
of the fact, that the detection zone should not be limited by non-transparent
objects (branch of trees and bushes, plants, mesh fences, etc). There must be
no items exposed to the temperature jumps within the detector visibility zone
(such as sun-heated wals and wall-parts).
1
3 4 5
6
7
8
9
10
11
12
13
14
15
BACKUP
MAIN
+
-
+
-
SENS.
RESET
HI
G
H
2
a) top view
b) side view
12 m
12 m
2.3 m
0
Figure 2 – Detection Pattern
