Riello 20151556 Скачать руководство пользователя страница 30

Страница: 30 / 32

COMMISSIONING AND MAINtENANCE

Led 1 Description

Remarks

4-way valve

malfunction

The alarm activates 5 minutes

after the unit start

The alarm activates when, in

Heating mode, the temperature

detected by the indoor unit heat

exchanger probe is less than or

equal to 15°C for 1 minute and for

3 times in an hour

Deviate from the

normal for the

compressor

The unit resets after problem

resolution

Power module

malfunction

After 3 consecutive interventions

in 10 minutes, the unit resets

after problem resolution

Electronic board

overtemperature

protection sensor

fault

After 3 consecutive interventions

in 1 hour, the unit resets after

problem resolution

Internal unit

overload

The unit resets after problem

resolution

Internal unit anti-

freeze protection

The alarm activates when the

indoor unit heat exchanger

probe is lower than the setpoint

for 2 minutes

The unit resets after problem

resolution

Compressor motor

overcurrent

The unit resets automatically

Overcurrent

protection for

single- phase of the

compressor

The unit resets after problem

resolution

In the presence of operating abnormalities, the unit is secured
and blocked.

Safety block can occur randomly.

Wait for at least 10 minutes before restarting the unit.

If the fault occurs again, an accurate check of the device
components is required. Contact

Technical Support

Service.

Indoor units with display signal faults with an alphanumeric
code. Consult the matching outdoor unit instruction booklet
for the installer.

Содержание 20151556

































Результаты поиска

Содержание 20151556

Отзывы:

Похожие инструкции для 20151556

Бренды по названию

Популярные бренды

Riello 20151556, Инструкции по установке и техническому обслуживанию

Результаты поиска

Содержание 20151556

Отзывы:

Похожие инструкции для 20151556

Бренды по названию

Популярные бренды