background image

PREPARING FOR EXTENDED PERIODS OF DISUSE

CLEANING

The combustion chamber and flue pipes must be 
cleaned periodically by the Technical Assistance 
Service or by a qualified heating engineer (see 
page 34).

If the boiler is not going to be used for an extended 
period of time, perform the following operations:

-  Turn the control panel power switch OFF and make 

sure that the green power indicator goes out

-  Turn the mains power switch OFF

- Close the fuel cock and heating circuit water cock

- Drain the central heating circuit if there is any risk of 

freezing

Contact 

r

 Technical Assistance Service if you 

encounter any problems in completing the above 
procedure.

Use a cloth damped in soapy water to clean the boiler’s 
external casing.
To remove stubborn marks, use a cloth damped in a 
50% mix of water and denatured alcohol or a suitable 
cleaning product.
Carefully dry the boiler after cleaning.

Do not use abrasive cleaning pads or powder deter-
gents.

Never clean the boiler without first disconnecting it 
from the mains electricity supply by turning the main 
power switch and the control panel switch OFF.

ON

OFF

15

SYSTEM MANAGER

Содержание 20106514





































Отзывы: