
2.
Enter SP5873 "SD Card Appli Move". Then move the application from the SD card in slot 2
to the card in slot 1.
3.
Exit the SP mode.
4.
Use caution when you do the SD Card Appli Move procedure:
• The necessary data for authentication is transferred with the application program from an SD
card to another SD card. Authentication fails if you try to use the SD card after you copy the
application program from one card to another card.
5.
Pull out the paper feed tray.
6.
Keep the SD card in the location [A] after you have copied the application program from
one card to another card.
This is done for the following reasons:
• 1) The SD card can be the only proof that the user is licensed to use the application program.
• 2) You may need to check the SD card and its data to solve a problem in the future.
Move Exec
The menu "Move Exec" (SP5-873-001) lets you copy application programs from the original SD card to
another SD card.
• Do not turn ON the write protect switch of an application SD card on the machine. If the write
protect switch is ON, a download error (e.g. Error Code 44) occurs during a firmware upgrade or
application merge.
1.
Turn the main switch off.
2.
Make sure that an SD card is in SD card slot 1. The application program is copied to this
SD card.
Controller Options
81
Содержание Z-P2
