Ricoh SP 230SFNw Скачать руководство пользователя

Страница: 56 / 255

2-35

Confidential



Error code 0501

The center thermistor of the fuser unit has not reached the specified temperature within the

specified time.

Error code 0502

The center thermistor of the fuser unit has not reached the specified temperature within the

specified time after it was heated normally to the certain level.

Error code 0503

The center thermistor of the fuser unit detected a temperature higher than the specified value.

Error code 0504

After the heat unit was heated normally, the center thermistor of the fuser unit detected a

temperature lower than the specified value.

Error code 0505

The center thermistor of the fuser unit detected a temperature rise greater than the specified

value within the specified time.

Error code 0506

The center thermistor of the fuser unit detected a temperature fall greater than the specified

value within the specified time.

Error code 0508

Temperature of the end part didn’t rise by 1 °C when the fuser unit heater was turned ON.

Error code 050A

The hardware detected a temperature error through the center thermistor or the side

thermistor of the fuser unit.

Error code 050B

When the center thermistor of the fuser unit was lower than the idle temperature, the side

thermistor detected a temperature higher than the specified temperature.

Error code 050C

When the center thermistor of the fuser unit was higher than the idle temperature, the side

thermistor detected a temperature lower than the specified temperature.

<User Check>

• Turn OFF the power switch. After several seconds, turn ON the power again and check that

this error is reset.

Step

Cause

Remedy

Connection failure of the center
or side thermistor harness of the
fuser unit

Reconnect the center or side thermistor
harness of the fuser unit.

Connection failure of the heater
harness of the fuser unit

Reconnect the heater harness of the fuser
unit.

Connection failure of the eject
sensor PCB harness

Reconnect the eject sensor PCB harness.

Connection failure of the low-
voltage power supply PCB harness

Reconnect the low-voltage power supply
PCB harness.

Eject sensor PCB failure

Replace the eject sensor PCB ASSY.

Fuser unit failure

Replace the fuser unit.

Low-voltage power supply PCB
failure

Replace the low-voltage power supply
PCB ASSY.

Main PCB failure

Replace the main PCB ASSY.

Содержание SP 230SFNw
































































































































































































































































Результаты поиска

Содержание SP 230SFNw

Отзывы:

Похожие инструкции для SP 230SFNw

Бренды по названию

Популярные бренды

Ricoh SP 230SFNw, Руководство по обслуживанию

Результаты поиска

Содержание SP 230SFNw

Отзывы:

Похожие инструкции для SP 230SFNw

Бренды по названию

Популярные бренды