Ricoh SP 230SFNw страница 236 Скачать руководство пользователя | Manualshive

Страница: 236 / 255

background image

5-31

Confidential

1.3.18 Print frame pattern (duplex printing) (Function code 70)

<Function>

This function is used to print the frame pattern on both sides of the paper to check for printing
flaws and omission.

<Operating Procedure>

(1) Set the paper specified in the default paper settings (A4 or Letter) to the paper tray.

(2) Press the [7], and then the [0] in the initial state of maintenance mode. For models

without keypad, press the [

▲

] or [

▼

] to display “MAINTENANCE 70” on the LCD and

press the [OK]. “PRINTING” is displayed on the LCD, and the frame pattern (refer to the
figure below) is printed on both sides of the paper.

(3) When printing is completed, “WAKU DX” is displayed on the LCD.

(4) Press the [X] or [Stop], and the machine returns to the initial state of maintenance mode.



Frame pattern

Fig. 5-11

Note:

If printing fails, printing is stopped with displaying any of the errors shown in the table below.
To retry printing, refer to the “Remedy” in the table below and eliminate the error cause and
press the [Start] or [Mono Start]. “PRINTING” is displayed on the LCD, and the frame pattern
is printed on both sides of a sheet of paper.

Error display

Remedy

Replace Toner

Replace the toner cartridge and press the [Start] or [Mono Start] to
release the error.

Cover is Open

Close the Front cover.

No Paper

Refill the paper, close the paper tray and press the [Start] or [Mono
Start] to release the error.

Jam Tray1

Remove the jammed paper, then close the paper tray and all
covers, press the [Start] or [Mono Start] to release the error.

Jam Rear
Jam Duplex
Duplex Disabled

Refill the paper, then close the paper tray and all covers, press the
[Start] or [Mono Start] to release the error.

«
...
234
235
236
237
238
...
»

Содержание SP 230SFNw
































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SP 230SFNw

CLP 510N - Color Laser Printer

Бренд: Samsung Страницы: 270

Bixolon SRP-270

Бренд: Samsung Страницы: 13

7760DN - Phaser Color Laser Printer

Бренд: Xerox Страницы: 158

Бренд: Oki Страницы: 94

Бренд: Ricoh Страницы: 126

AltaLink C81 Series

Бренд: Xerox Страницы: 412

Бренд: Epson Страницы: 4

Бренд: Epson Страницы: 36

Бренд: Epson Страницы: 4

Бренд: Epson Страницы: 115

Бренд: Epson Страницы: 248

Бренд: Epson Страницы: 108

Бренд: Epson Страницы: 298

Бренд: Epson Страницы: 4

imageRUNNER C3120

Бренд: Canon Страницы: 20

imageRUNNER C3170 series

Бренд: Canon Страницы: 12

imageRUNNER C3170 series

Бренд: Canon Страницы: 45

ImageRunner C2550

Бренд: Canon Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды