Ricoh SP 230SFNw Скачать руководство пользователя страница 212

Страница: 212 / 255

5-7

Confidential

1.3.5 Check LCD operation (Function code 12)

<Function>

This function is used to check that the LCD on the control panel is operating normally.

<Operating Procedure>

(1) Press the [1], and then the [2] in the initial state of maintenance mode. For models

without keypad, press the [

▲

] or [

▼

] to display “MAINTENANCE 12” on the LCD and

press the [OK]. Displays shown in the figure below appear on the LCD.

(2) Each press of the [Start] cycles through the displays as shown in the figure below.

(3) Press the [Stop], and the machine returns to the initial state of maintenance mode.

Fig. 5-2

Display 5

Display 4

Displays all dots

Displays 16 frames in a line

Displays no dots

Displays Lattice

Display 1

Back light : ON

Displays “ɥ”

Display 6

Displays no dots

Display 2

Display 3

Back light : ON

Back light : OFF

Содержание SP 230SFNw
































































































































































































































































Результаты поиска

Содержание SP 230SFNw

Отзывы:

Бренды по названию

Популярные бренды

Ricoh SP 230SFNw, Руководство по обслуживанию

Результаты поиска

Содержание SP 230SFNw

Отзывы:

Бренды по названию

Популярные бренды