Ricoh Ri 100 Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 260

background image

Loading Fabrics

This section explains the procedures for loading fabrics.

• When loading or removing fabrics, keep your hands or fingers clear of the cassette. Otherwise,

your hands or fingers might get caught, resulting in injury.

Loading a Fabric in the Standard Tray

This section explains how to load a fabric in the A4 standard tray. The same operation applies when the
A5 tray is used.

• When printing on thin fabrics, the ink may adhere to the table. Place paper or something similar on

the table before loading the fabric.

1.

Press the [Power] key.

Remove the cassette after turning the power on. If the cassette is mistakenly removed before turning
the power on, turn the power off once, and then turn the power on again.

2.

Check that the cassette stand comes to the front.

If the cassette stand does not come to the front, press the [Tray] key and move the cassette to the
front.

3.

Lift the cassette slightly, pull it to the front to remove it.

4.

Press the unlock button and lift the cover.

DSA348

5.

Put marks on the fabric for when loading it in the cassette.

The image will be printed in the direction from the front side to the back side of the cassette. Turn
the protection cover inside out and put it on the fabric in the direction as shown in the figure, and
then put marks using a marking pen or the like by putting it through the holes of the protection
cover.

2. Preparing for Printing

72

«
...
72
73
74
75
76
...
»

Содержание Ri 100





































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Ri 100

Бренд: Oki Страницы: 20

imageRUNNER ADVANCE C350iF

Бренд: Canon Страницы: 102

imageRUNNER ADVANCE C2230

Бренд: Canon Страницы: 12

Бренд: Canon Страницы: 598

Бренд: Canon Страницы: 21

Бренд: Canon Страницы: 23

Hi-Res EBS-2600

Бренд: EBS Ink-Jet Systems Страницы: 3

Бренд: iDPRT Страницы: 74

Бренд: Memjet Страницы: 181

Pro C5300 Series

Бренд: Ricoh Страницы: 37

Бренд: Epson Страницы: 8

Бренд: Epson Страницы: 20

Бренд: Epson Страницы: 10

Бренд: Epson Страницы: 8

Stilus CX9300F Series

Бренд: Epson Страницы: 44

Бренд: Epson Страницы: 2

Бренд: Epson Страницы: 50

Бренд: Epson Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды