Ricoh Ri 100 Скачать руководство пользователя страница 125 | Manualshive

Страница: 125 / 260

background image

1.

Press the [Tray] and [Stop] keys at the same time.

DSB256

The following message appears:

Press # to
clean heads

2.

Press the [#Enter] key.

Head cleaning starts.

Head-flushing

Follow the procedure below to perform a thorough print head cleaning. Because head flushing
consumes more ink than head cleaning, do it only if the print head cannot be cleaned properly by head
cleaning.
When the ink cartridge is empty, replace it instead of performing a print head cleaning. After an ink
cartridge is replaced, a print head cleaning will be automatically performed.

• Do not turn the machine off during print head cleaning. If the machine is turned off during print

head cleaning, start again from the beginning.

1.

Press the [ /Menu] key.

2.

Press the [ ] or [ /Menu] key to display [Maintenance], and then press the [#Enter] key.

<Menu>
Maintenance

3.

Press the [ ] or [ /Menu] key to display [Head-flushing], and then press the [#Enter]
key.

<Maintenance>
Head-flushing

Using the [Maintenance] Menu

123

«
...
123
124
125
126
127
...
»

Содержание Ri 100





































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Ri 100

Бренд: Oki Страницы: 24

Бренд: VAF instruments Страницы: 24

Бренд: TDT Страницы: 15

Бренд: Xerox Страницы: 8

Бренд: BadgePass Страницы: 2

Бренд: Oki Страницы: 24

imageRUNNER 4570

Бренд: Canon Страницы: 154

Бренд: Canon Страницы: 4

Бренд: Oce Страницы: 340

Бренд: Muratec Страницы: 112

WorkCentre XD Series

Бренд: Xerox Страницы: 63

Phaser 6700V/DX

Бренд: Xerox Страницы: 162

Бренд: Xerox Страницы: 78

Бренд: MIMAKI Страницы: 20

Genmitsu 3018-MX3

Бренд: SainSmart Страницы: 50

Бренд: Lanier Страницы: 140

Бренд: TEC Страницы: 92

Бренд: Kyocera Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды