Ricoh Kr-P2 Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 200

background image

7. Firmware names are displayed on the LCD.
8. Scroll to the program to upgrade, then press [OK].
9. Press the [UPDATE] to start the upgrade.

Loading
*****************

Update done
xxxxxxxxx

10. "Update done" appears on the LCD after completing the firmware updating.
11. Turn off the power, remove the SD card from Slot 2, and turn on the power.

-or-
If you intend to update another program, leave the SD card in Slot 2 and turn off and on the power.

• The firmware has not updated successfully if the "Update done" message does not appear. If

this occurs, turn the machine power off/on and repeat the procedure.

Error Recovery

Controller

If an error occurs during updating the controller firmware, use the following procedure. This procedure will
force the controller to boot from the firmware SD card.

1. Prepare an SD card with the required controller firmware version.
2. Turn off the machine and remove the controller.

Updating the Firmware

81

5

«
...
81
82
83
84
85
...
»

Содержание Kr-P2









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Kr-P2

Бренд: NCR Страницы: 36

Бренд: NCR Страницы: 206

Бренд: NCR Страницы: 138

Бренд: Magicard Страницы: 26

Бренд: QMS Страницы: 194

Бренд: Z Corporation Страницы: 4

Бренд: CAB Страницы: 40

DocuPrint C3055 DX

Бренд: Xerox Страницы: 20

Бренд: Olivetti Страницы: 438

da Vinci 1.0 Pro

Бренд: XYZ Printing Страницы: 11

WorkCentre Pro 32

Бренд: Xerox Страницы: 14

Бренд: Olivetti Страницы: 82

Бренд: Alunar Страницы: 6

AirLive WP-203G

Бренд: Ovislink Страницы: 132

Бренд: SPRT Страницы: 48

Бренд: Konica Minolta Страницы: 102

STREAM MK3 Series

Бренд: VOLUMIC Страницы: 70

Бренд: Fujitsu Страницы: 126

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды