Ricoh Kr-P2 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 200

background image

Machine Installation

Main Unit and Option Unit

Refer to the "Hardware Guide" for M041 model about the machines installation.

Printer Option

Refer to the "Hardware Guide" for M041 model about the machines installation. If more than two optional
applications are supposed to be installed, do "SD Card Appli Move" described below.

• IPDS option requires an optional memory (128 MB or 256 MB). Install an optional memory first

before installing the IPDS option. Otherwise, the machine may stall when large print job data is sent
to the machine.

SD Card Appli Move

Overview

The service program "SD Card Appli Move" (SP5-873) lets you to copy application programs from one
SD card to another SD card.
Slot 1 and Slot 2 are used to store application programs. However, more than two optional applications
are supplied for this machine. In that case, you can move application programs from Slot 2 to Slot 1 with
the following procedure.
Obey these precautions during the SD Card Appli move procedure:

• The authentication data is moved with the application program from an SD card to the other SD card.

Authentication fails if you try to use the SD card after you move the application program from this card
to another SD card.

• Do not use an SD card if it has been used for some other work, for example, on a computer. Normal

operation is not guaranteed when such SD card is used.

• Store the original SD card in a safe location after the procedure. The original SD card cannot be used

but it must be saved because (1) the original card is the only proof that the user is licensed to use the
application program, and (2) you may need to check the SD card and its data to solve a problem in
the future.

Machine Installation

17

2

«
...
17
18
19
20
21
...
»

Содержание Kr-P2









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Kr-P2

Бренд: GCC Technologies Страницы: 14

Бренд: Panasonic Страницы: 9

Бренд: Panasonic Страницы: 2

Бренд: zortrax Страницы: 11

Бренд: Konica Minolta Страницы: 15

Бренд: Triumph Adler Страницы: 4

Бренд: Intuitive Страницы: 18

HP Toner Cartridges 6R941

Бренд: Xerox Страницы: 2

Бренд: ColorGATE Страницы: 6

Бренд: WANHAO Страницы: 18

Бренд: SPRT Страницы: 14

BradyPrinter A5500

Бренд: Brady Страницы: 72

Бренд: Oki Страницы: 246

Бренд: Printronix Страницы: 148

Бренд: Canon Страницы: 342

Бренд: Canon Страницы: 454

Бренд: Canon Страницы: 498

Бренд: Canon Страницы: 563

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды