Ricoh Aficio MP 2500 Скачать руководство пользователя страница 49

Страница: 49 / 204

Placing Originals

Transmission with Image Rotation

Generally, place A4, 8

11" originals in the landscape orientation (

). If you

place an A4, 8

11" original in the portrait orientation (

), the image is sent

rotated by 90

. Providing the receiver has A4, 8

11" landscape paper (

the document is printed the same size as the original.

Note

❒

This function is unavailable with Immediate Transmission.

Stamp

When sending a fax document using the ARDF, the machine can stamp a circle
mark at the bottom of the original.
When sending a two-sided document, the document is marked at the bottom of
the front page and top of the rear page.

Important

❒

The optional ARDF is required.

❒

Stamp only works when scanning from the ARDF.

❒

This function must be registered to a User Function key in advance. It is reg-
istered to the User Function key

{

}

by default.

Place the original, and then select the scan settings you require.

Press the User Function key

{

}

to light the indicator.

To cancel the stamp, press the User Function key

{

}

again to turn off the indicator.

ARX024S

Содержание Aficio MP 2500













































































































































































































Результаты поиска

Содержание Aficio MP 2500

Отзывы:

Похожие инструкции для Aficio MP 2500

Бренды по названию

Популярные бренды

Ricoh Aficio MP 2500, Руководство по факсимильной связи

Результаты поиска

Содержание Aficio MP 2500

Отзывы:

Похожие инструкции для Aficio MP 2500

Бренды по названию

Популярные бренды