Ricoh Aficio MP 2500 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 204

background image

Transmission

20

1

If memory runs out while storing an original

If you run out of memory while storing an original (free space reaches 0%), the
“

Memory is full. Scanning will be stopped and only scanned page(s)

will be stored.

” message appears. Press

[

Exit

]

to transmit stored pages only.

Note

❒

When this happens, only the scanned pages are sent. If you want to delete the
scanned pages and cancel transmission in this case, contact your service rep-
resentative.

ECM (Error Correction Mode)

If part of a transmission fails because of a line problem, the lost data is automat-
ically resent.

Important

❒

For this function to work, the other machine must have ECM.

❒

This function is not available with Internet Fax.

Immediate Transmission

Immediate Transmission is possible with standard fax transmission and IP-Fax
transmission.

Important

❒

Internet Fax is executed in only Memory Transmission that starts transmis-
sion automatically after storing documents in memory.
• If you specify an Internet Fax destination after selecting Immediate Trans-

mission, the mode switches to Memory Transmission.

• If you try to select Immediate Transmission after specifying an Internet Fax

destination, the “

Dest. and functions that could not be specified

on immediate transmission is already selected.

” message appears.

When this happens, press

[

Exit

]

.

❒

Group cannot be used for Immediate Transmission. You cannot send the
same document to multiple destinations (broadcasting).
• If you specify a second destination or a group after selecting Immediate

Transmission, the mode switches to Memory Transmission.

• If you try to select Immediate Transmission after specifying multiple des-

tinations or a group, the “

Dest. and functions that could not be

specified on immediate transmission is already selected.

”

message appears. When this happens, press

[

Exit

]

.

«
...
28
29
30
31
32
...
»

Содержание Aficio MP 2500













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Aficio MP 2500

imagePROGRAF iPF8300S

Бренд: Canon Страницы: 52

Бренд: Canon Страницы: 2

Бренд: Oki Страницы: 2

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 341

Бренд: Samsung Страницы: 8

CLX2160N - Color Laser - All-in-One

Бренд: Samsung Страницы: 118

CLX 3160FN - Color Laser - All-in-One

Бренд: Samsung Страницы: 142

CLP-770ND - Color Laser Printer

Бренд: Samsung Страницы: 2

CLP 610ND - Color Laser Printer

Бренд: Samsung Страницы: 114

Бренд: Samsung Страницы: 6

Бренд: Samsung Страницы: 15

CLP 600N - Color Laser Printer

Бренд: Samsung Страницы: 227

CLP 600N - Color Laser Printer

Бренд: Samsung Страницы: 118

CLP 300N - Network-ready Color Laser Printer

Бренд: Samsung Страницы: 94

CJX-2000FW Series

Бренд: Samsung Страницы: 2

4116 - SCX B/W Laser

Бренд: Samsung Страницы: 205

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды