Ricoh Aficio MP 1600 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 204

background image

5

How to Read This Manual

Symbols

This manual uses the following symbols:

Indicates important safety notes.
Ignoring these notes could result in serious injury or death. Be sure to read these
notes. They can be found in the “Safety Information” section of About This Machine.

Indicates important safety notes.
Ignoring these notes could result in moderate or minor injury, or damage to the
machine or to property. Be sure to read these notes. They can be found in the
“Safety Information” section of About This Machine.

Indicates points to pay attention to when using the machine, and explanations
of likely causes of paper misfeeds, damage to originals, or loss of data. Be sure
to read these explanations.

Indicates supplementary explanations of the machine's functions, and instruc-
tions on resolving user errors.

This symbol is located at the end of sections. It indicates where you can find fur-
ther relevant information.

[

]

Indicates the names of keys that appear on the machine's display panel.

{

}

Indicates the names of keys on the machine's control panel.

Names of Major Options

Major options of this machine are referred to as follows in this manual:
• Auto Document Feeder

→

ADF

• Auto Document Feeder capable of scanning both side of a sheet

→

ARDF

Names of Major Functions

This machine's major functions are referred to in this manual as follows:
• Internet Fax (by specifying an e-mail address)

→

Internet Fax

• Internet Fax (by specifying an IPv4 address)

→

IP-Fax

«
...
13
14
15
16
17
...
»

Содержание Aficio MP 1600













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Aficio MP 1600

Бренд: Zeka Страницы: 54

Бренд: Canon Страницы: 21

Бренд: Canon Страницы: 23

Бренд: idp Страницы: 104

Бренд: Xerox Страницы: 3

imageRUNNER ADVANCE DX C5870i

Бренд: Canon Страницы: 100

imageRUNNER ADVANCE C356iF

Бренд: Canon Страницы: 96

imageRUNNER ADVANCE C350 series

Бренд: Canon Страницы: 1173

imageRUNNER ADVANCE DX 6870i

Бренд: Canon Страницы: 100

imageRUNNER ADVANCE 715iFZ III

Бренд: Canon Страницы: 92

ImageRUNNER C1538iF

Бренд: Canon Страницы: 120

imageRUNNER ADVANCE DX 717iFZ

Бренд: Canon Страницы: 92

imageRUNNER ADVANCE DX C568iFZ

Бренд: Canon Страницы: 92

Бренд: Epson Страницы: 61

Бренд: Epson Страницы: 4

Бренд: Epson Страницы: 4

Бренд: Epson Страницы: 5

Бренд: Epson Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды