Ricoh Aficio IS 2325 Скачать руководство пользователя страница 50

Страница: 50 / 126

Troubleshooting When Using the Printer Function

When a Message Is Displayed

This section describes the principal messages that appear on the display panel.
If a message not described here appears, act according to the message.

Note

❒

Before turning the main power off, see “Turning On the Power”, About This
Machine.

Reference

“Turning On the Power”, About This Machine

Status Messages

This section describes the machine status messages.

Message

Status

Ready

This is the default ready message. The machine is ready
for use. No action is required.

Waiting...

The machine is waiting for the next data to print. Wait a
while.

Offline

The machine is offline. To start printing, switch the ma-
chine online by pressing the

{

Online

}

Key.

Please wait...

This message may appear for a second or two while the
machine is preparing, performing initial adjustments, or
adding toner. Wait a while.

Hex Dump Mode

In Hex Dump mode, the machine prints received data in
hexadecimal format. Turn off the machine after printing,
and then turn back on.

Resetting Job...

The machine is resetting the print job. Wait until
“

Ready

” appears on the display panel.

Setting change...

The machine settings are being changed. Wait a while.

Содержание Aficio IS 2325































































































































Результаты поиска

Содержание Aficio IS 2325

Отзывы:

Похожие инструкции для Aficio IS 2325

Бренды по названию

Популярные бренды

Ricoh Aficio IS 2325, Инструкции по эксплуатации и устранению неисправностей

Результаты поиска

Содержание Aficio IS 2325

Отзывы:

Похожие инструкции для Aficio IS 2325

Бренды по названию

Популярные бренды