Ricoh Aficio IS 2325 Скачать руководство пользователя страница 29

Страница: 29 / 126

3. Troubleshooting When

Using the Facsimile Function

This chapter describes likely causes of and possible solutions for facsimile func-
tion problems.

Adjusting the Volume

The following describes how to adjust the volume.
You can change the volume of the following sounds that the machine makes.

❖

On Hook Mode

Heard when the

{

On Hook Dial

}

key is pressed.

❖

At Transmission

Heard when immediate transmission is performed.

❖

At Reception

Heard when the machine receives a document.

❖

At Dialing

Heard after pressing the

{

Start

}

key, until the line connects to the destination.

❖

At Printing

Heard when a received document is printed.

Press the

{

User Tools/Counter

}

key.

Select

[

Fax Features

]

using

{U}

{T}

, and then press the

{

}

key.

BAK013S

Содержание Aficio IS 2325































































































































Результаты поиска

Содержание Aficio IS 2325

Отзывы:

Похожие инструкции для Aficio IS 2325

Бренды по названию

Популярные бренды

Ricoh Aficio IS 2325, Инструкции по эксплуатации и устранению неисправностей

Результаты поиска

Содержание Aficio IS 2325

Отзывы:

Похожие инструкции для Aficio IS 2325

Бренды по названию

Популярные бренды