Ricoh Aficio FX10 Скачать руководство пользователя страница 220

Страница: 220 / 284

7.1.13. Unfused Copies

Possible Cause (Printer)

•

The thermistor is defective.

•

The fusing pressure roller spring mechanism is defective.

•

The wrong type of toner is being used.

•

A non-recommended type of paper is being used.

Action:

1. Check if the correct type of paper and toner are being used.

•

If it is, go to step 2.

•

If not, use recommended types of paper and toner.

2. Try replacing the fusing lamp and the roller.

7.1.14. Ghost Image

Possible Cause (Printer)

•

Poor drum sensitivity.

•

The cleaning blade is deformed or incorrectly positioned.

•

Dirty hot roller

Action:

•

Clean the cleaning blade.

•

Replace the CTM.

•

Clean the hot roller surface and/or replace the cleaning pad.

•

Replace the drum.

roub

oot

June 10th, 1997

TROUBLESHOOTING

COPY QUALITY TROUBLESHOOTING

7-15

Содержание Aficio FX10





























































































































































































































































































Результаты поиска

Содержание Aficio FX10

Отзывы:

Похожие инструкции для Aficio FX10

Бренды по названию

Популярные бренды

Ricoh Aficio FX10, Руководство по обслуживанию

Результаты поиска

Содержание Aficio FX10

Отзывы:

Похожие инструкции для Aficio FX10

Бренды по названию

Популярные бренды