background image

Series RMA-B

  

close-coupled design

 

Page 

 

 

9450-055-en 

Revision  01 

TM 9886

 

Edition  11/2018 

1.1  Tightening torques 

Screws greased, tighten in diametrically opposite 

sequence 

Housing screws 901/3 

Size  

No. x size 

Tightening torque 

[inch] 

[ASME] 

[in-lbs] 

[Nm] 

1,5"x1"x6" 

8 x ½“ 

415 

47 

3"x1,5"x6" 

8 x ½“ 

415 

47 

3"x2"x6" 

8 x ½“ 

415 

47 

1,5"x1"x8" 

10 x ½“ 

390 

44 

3"x1,5"x8" 

12 x ½“ 

415 

47 

3"x2"x8" 

12 x ½“ 

415 

47 

4"x3"x8" 

12 x ½“ 

415 

47 

3"x2"x10" 

12 x 

5

/

8

“ 

743 

84 

4"x3"x10"H 

12 x 

5

/

8

“ 

743 

84 

6"x4"x10" 

12 x 

5

/

8

“ 

743 

84 

 

Pipe screws, flanges to ASME B16.5 Class 150

 

DN  

No. x size 

Tightening 

torque 

[inch] 

[ASME] 

[in-lbs]  [Nm] 

1“ 

4 x ½“ 

70 

1½“ 

4 x ½“ 

135 

15 

2“ 

4 x 5/8“ 

220 

25 

3“ 

4 x 5/8“ 

400 

45 

4“ 

8 x 5/8“ 

310 

35 

6“ 

8 x 

5

/

8

“ 

310 

35 

 

1.2  Type plate, dry-running, ATEX and 

housing markings 

The stainless steel type plate is undetachably riveted 

to the adapter. 
If the operator attaches his identification, it must be 

ensured that the pump matches the application in 

question.  

Example of type plate: 

 

 

Dry-running: 

 

 

ATEX marking: 

 

 

 

Housing identification: 

The following are visible on the housing according to 

DIN EN 19: 

  Nominal size 

  Rated pressure 

  Housing material 

  Manufacturer's identification 

  Melt number/Foundry identification 

  Cast date 

 

 

1.3  Spareparts 

Spare parts for two years of continuous operation in 

accordance with DIN 24296 and in consultation with 

the manufacturer 

 

Содержание RMA Series





































Отзывы: