Rice Lake REVOLUTION 682 Synergy Plus Скачать руководство пользователя страница 72

Страница: 72 / 130

682 Synergy Plus

Visit our website

www.RiceLake.com

9.0

Wi-Fi & Bluetooth® Communications

The 682 is a Wi-Fi and/or Bluetooth® device. The following sections provide details on Wi-Fi and Bluetooth® communications

and describe the procedures required to configure these features.
The 682 features a Lantronix

xPico 200 Series wireless module. Visit

www.lantronix.com

to view the xPico 200 Series User

Guide for detailed instructions on the module.

NOTE: The use of a web browser on a computer or handheld device is needed to access the wireless module’s built-in Web

Manager. See

Section 3.4.17 on page 26

to view the Wi-Fi and Bluetooth® MAC Addresses from the 682 display.

Soft AP (Access Point) Details

• Name:

RLWS_XXXXXX

• Password:

PASSWORD

• Configuration Page:

http://192.168.0.1

NOTE: The Soft AP only shows up as a 5-GHz network. The connecting device must be capable of using the 5 GHz band to

connect to the Soft AP. Setup → Communications → WiFi & Bluetooth → Enabled defaults to Off and must be set to WiFi,

Bluetooth or Both to enable Wi-Fi & Bluetooth communications and allow the Soft AP to be available.

9.1 Bluetooth® Communications

To enable Bluetooth® for the 682 indicator, navigate to Setup → Communications → WiFi & Bluetooth → Enabled, and select

Bluetooth or Both. This parameter is only accessible in

Setup

mode (

Section 4.1 on page 29

Once enabled, scan for available Bluetooth® devices on the device that is intended to be paired with the 682 and pair the

intended Bluetooth® device with the 682 wireless module’s Bluetooth® connection. The 682 wireless module’s Bluetooth®

device name is

RLWS_XXXXXXXXXXXX

NOTE: The X’s in the name represent the entire Bluetooth® MAC address.

9.2 Wi-Fi Communications

The 682 creates a Wi-Fi network that can be connected to with a computer or the location’s network. Configuration of the

wireless settings is done through the built-in Web Manager. The Web Manager can be accessed through the built-in Soft AP

(Access Point). The Soft AP can be used to connect to a location’s network using the Web Manager. In applications that don’t

have a local network to connect to or if the network is not in range, the Soft AP connection can also be used to talk to a 682 by

connecting to IP 192.168.0.1, port 10001.

9.2.1 Wi-Fi Setup

The following procedure is for setting up the Wi-Fi network using the wireless module’s built-in Web Manager.

1. Power on the 682 indicator.
2. To enable the wireless module and specify wireless communications in the 682 menu:

• In

Setup

mode (

Section 4.1 on page 29

), navigate to Setup → Communications → WiFi & Bluetooth → Enabled,

and set to WiFi or Both.

• Return to

Weigh

mode to allow the change to initialize.

Содержание REVOLUTION 682 Synergy Plus



































































































































Результаты поиска

Содержание REVOLUTION 682 Synergy Plus

Отзывы:

Похожие инструкции для REVOLUTION 682 Synergy Plus

Бренды по названию

Популярные бренды

Rice Lake REVOLUTION 682 Synergy Plus, Техническое руководство

Результаты поиска

Содержание REVOLUTION 682 Synergy Plus

Отзывы:

Похожие инструкции для REVOLUTION 682 Synergy Plus

Бренды по названию

Популярные бренды