manualshive.com logo in svg

Rice Lake MSI-4260M, Техническое руководство

Поделиться
Скачать
Rice Lake MSI-4260M Скачать руководство пользователя страница 5

Introduction

© Rice Lake Weighing Systems

 

●

 All Rights Reserved

1

1.0

Introduction

The MSI-4260M Port-A-Weigh crane scale has an established reputation as the industry standard in medium to heavy-capacity 

overhead weighing and duty-cycle needs. With a proven mechanical design and advanced electronics, the MSI-4260M is 

versatile, reliable, accurate and user friendly.
The MSI-4260M is designed to meet or exceed requirements of applicable ASME, ANSI, OSHA

 

safety standards.

Multiple options and accessories, including the RF Rugged Remote Control and RF remote displays are available to further 

enhance the performance and application versatility of the MSI-4260M.

Manuals and additional resources are available from the Rice Lake Weighing Systems website at 

www.ricelake.com

Warranty information can be found on the website at 

www.ricelake.com/warranties

1.1 Safety 

Safety Signal Definitions:

Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury. Includes 

hazards that are exposed when guards are removed.
Indicates a potentially hazardous situation that, if not avoided, could result in serious injury or death. Includes 

hazards that are exposed when guards are removed.

  Indicates a potentially hazardous situation that, if not avoided, could result in minor or moderate injury.

Indicates information about procedures that, if not observed, could result in damage to equipment or corruption 

to and loss of data.

General Safety

Do not operate or work on this equipment unless this manual has been read and all instructions are understood. 

Failure to follow the instructions or heed the warnings could result in injury or death. Contact any Rice Lake 

Weighing Systems dealer for replacement manuals. 

Failure to heed could result in serious injury or death.

Do not allow minors (children) or inexperienced persons to operate this unit.
Do not stand near the load being lifted as it is a potential falling hazard. Keep a safe distance.
Do not use for purposes other then weight taking or dynamic load monitoring.
Do not use any load bearing component that is worn beyond 5% of the original dimension.
Do not use the scale if any of the components of the load train are cracked, deformed or show signs of fatigue.
Do not exceed the rated load limit of the scale, rigging elements or the lifting structure.
Do not allow multi-point contact with the hook, shackle or lifting eye of the scale.
Do not allow high torque on the scale unless it is specifically designed for high torque.
Do not make alterations or modifications to the scale or associated load bearing devices.
Do not use improperly rated or sized shackles. Use only Rice Lake Weighing Systems recommended shackles.
Do not remove or obscure warning labels.
For guidelines on the safe rigging and loading of overhead scales, read the Rice Lake Weighing Systems Crane Scale Safety and 

Periodic Maintenance Manual (available at www.ricelake.com).
Keep hands, feet and loose clothing away from moving parts.
There are no user serviceable parts within the MSI-4260M. Any repairs are to be performed by qualified service personnel only.
The MSI-4260M Port-A-Weigh scale has a safe mechanical overload of 200% and an ultimate overload of 500%. Overloads greater 

than 50% could result in structural failure and dropped loads. Dropped loads could cause serious personal injury or death.

DANGER

WARNING

CAUTION

IMPORTANT

WARNING

Содержание MSI-4260M







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды